The AirTAC AirTAC SE100X600SH ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 600mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X600SH is a double-acting single-rod profile cylinder built to ISO 15552 dimensions, delivering a robust 3927 N push at 0.5 MPa. Its extruded aluminum barrel omits external tie rods, yielding a flush outer surface that simplifies mounting and resists corrosion in harsh environments. The FKM (Viton) seal expands the operating temperature window up to 150 C, making it well-suited for hot manufacturing zones.
Equipped with a built-in position magnet, this unit integrates seamlessly with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable pneumatic cushioning at both ends allows technicians to tune deceleration via a set screw, softening hard impacts when moving heavy loads across the 600 mm stroke.
| Model | AirTAC SE100X600SH ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the high 5497 N push force at 0.7 MPa needed to eject dense plastic parts from hot molds, utilizing the FKM seal to withstand ambient radiant heat up to 150 C.
Drives heavy stamping presses across a 600 mm travel to shear flash from aluminum castings, relying on adjustable end cushions to absorb kinetic energy and protect the tooling.
Actuates large-scale pallet diverter arms in high-throughput logistics lines, using the integrated magnet to trigger DMSE solid-state sensors for precise mid-stroke positioning.
This 100 mm bore generates 3927 N of push force at 0.5 MPa. If your application requires less thrust, stepping down to the 80 mm bore yields 2513 N, while moving up to the 125 mm bore provides 6136 N. Because the 600 mm stroke is substantial, the Ø25 mm piston rod and internal bearing face increased bending moments under side loads; always pair this cylinder with an external guide rail to prevent premature seal wear.
As a standard ISO 15552 profile cylinder, it serves as a drop-in dimensional replacement for comparable 100 mm bore cylinders using the same PT1/2 port and mounting footprint. Note that the adjustable air cushion only decelerates the piston near the end of travel—it does not lock or hold the load. If air pressure is lost, the rod will drift, requiring a BSE rod lock for secure positioning.
Quick checklist
At 0.5 MPa, this 100 mm bore cylinder provides 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force increases to 5497 N. The maximum push force is 801 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.
Yes, the SE100X600SH is dimensionally interchangeable with any standard ISO 15552 profile cylinder. It shares the same standardized mounting dimensions, PT1/2 port size, and M20x1.5 rod thread, allowing for a direct drop-in retrofit without modifying your existing machinery.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.