The AirTAC AirTAC SE100X630S ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 630mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X630S is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty linear motion. It features a 100 mm bore and a 630 mm stroke, generating 3927 N of push force at 0.5 MPa and up to 5497 N at 0.7 MPa. The extruded aluminum barrel lacks external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while freeing up the three integrated sensor grooves for position detection.
Because this configuration includes the -S magnet code, it is fully primed for AirTAC CMSE reed and DMSE electronic sensors to track piston position mid-stroke. The cylinder relies on field-adjustable pneumatic cushioning at both ends to decelerate the heavy 100 mm piston over its 36 mm cushion length, softening hard end stops at high cycle speeds. Note that this adjustable cushion only acts as an end-of-stroke damper; it does not lock or hold the load if air pressure drops.
| Model | AirTAC SE100X630S ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 630 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×630 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 3927 N push force at 0.5 MPa needed to compress and stack heavy pallets of corrugated packaging, using the 630 mm stroke to reach lower machine tiers.
Automates the loading and unloading of heavy sheet metal blanks into forming presses, where the 100 mm bore's 5497 N extension force at 0.7 MPa easily shoves parts into die locators.
Moves heavy vehicle chassis components across a 630 mm span for robotic spot welding, relying on the -S magnet and DMSE sensors to confirm part handoff position.
Delivering 3927 N push at 0.5 MPa, this 100 mm bore is a robust choice for high-force tasks. If your application requires less energy, stepping down to the 80 mm bore yields 2513 N of push force at 0.5 MPa. Conversely, moving up to the 125 mm bore provides 6136 N at 0.5 MPa for heavier loads. Since the 630 mm stroke exceeds 300 mm, the unsupported rod length increases the risk of rod-bearing bending under side loads; integrating an external guide rail is highly recommended to prevent premature seal wear.
As a dimensionally interchangeable ISO 15552 cylinder, the SE100X630S serves as a drop-in replacement for other ISO 15552 profile cylinders, utilizing the same mounting hardware and a PT1/2 port. Remember that a standard double-acting cylinder drifts when air is exhausted; if your machine must hold a vertical load safely without live pressure, consider the AirTAC BSE rod-lock variant instead.
Quick checklist
At 0.5 MPa, the 100 mm bore provides 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force increases to 5497 N, with a maximum push capacity of 801 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, it is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting interface and body dimensions as other ISO 15552 profile cylinders. However, it is a double-acting cylinder and will drift if air is lost; the adjustable air cushion only decelerates the piston near stroke end and does not lock the load.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.