The AirTAC AirTAC SE100X650SH ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 650mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X650SH is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty positioning. It delivers a substantial 3927 N push at 0.5 MPa, utilizing a 100 mm bore and a 650 mm stroke to move high-mass loads. Equipped with a Viton (FKM) seal, this unit reliably operates in elevated ambient temperatures up to 150 C where standard elastomers would fail.
Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. The integrated -S magnet enables precise end-position detection using AirTAC CMSE reed or DMSE electronic sensors housed neatly within the body's multiple sensor grooves.
| Model | AirTAC SE100X650SH ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 650 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×650 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 5497 N push at 0.7 MPa required to eject dense plastic parts from hot mold tooling, leveraging the FKM seal to withstand ambient radiated heat up to 150 C.
Actuates a heavy diverter arm across a 650 mm stroke to re-route loaded pallets on a high-speed packaging line, absorbing the kinetic energy via field-adjustable pneumatic cushions.
Advances thick metal blanks into a stamping press, utilizing the 25 mm hard-chrome rod to maintain structural integrity under high axial loads and repetitive cycling.
Selecting this 100 mm bore makes sense when a 80 mm cylinder's 2513 N push at 0.5 MPa is insufficient for your payload, but you want to avoid stepping up to a massive 125 mm unit. Because the 650 mm stroke creates a long lever arm, side loading places significant bending stress on the rod bearing; always pair this cylinder with an external guide rail to prevent premature seal wear. As a true ISO 15552 profile cylinder, it serves as a drop-in dimensional replacement for other ISO 15552 cylinders, sharing standard mounting accessories and PT1/2 ports. Note that the adjustable air cushions only decelerate the piston near stroke end and cannot hold a load if air pressure drops—specify a BSE rod lock for fail-safe positioning.
Quick checklist
At 0.5 MPa, this 100 mm bore cylinder provides 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force increases to 5497 N. The maximum push capacity is 801 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.
Yes, it is dimensionally interchangeable with any standard ISO 15552 profile cylinder and uses the same mounting interface and PT1/2 ports. However, the adjustable air cushion only decelerates the piston near the end of stroke; it cannot hold a load vertically or resist drift if air pressure is lost. For position holding, you need a BSE series rod lock.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.