The AirTAC AirTAC SE100X665SH ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 665mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X665SH is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty positioning. It delivers a substantial 3927 N push force at 0.5 MPa, utilizing a 100 mm bore and a 665 mm stroke. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while retaining the standardized ISO 15552 footprint.
Equipped with an S suffix magnet, this unit directly interfaces with AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The H designation specifies a high-temperature FKM seal, widening the operating envelope from -20 up to 150 C for demanding thermal environments. Field-adjustable air cushions at both ends allow technicians to tune end-of-stroke deceleration, protecting payloads from hard mechanical impacts.
| Model | AirTAC SE100X665SH ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 665 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×665 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 5497 N extend force at 0.7 MPa needed to positively eject dense plastic parts from hot mold tooling, leveraging the FKM seal to withstand ambient radiant heat up to 150 C.
Utilizes the full 665 mm stroke to raise or lower heavy timber pallets between conveyor tiers, where the integrated magnet triggers DMSE sensors to confirm load transfer.
Shoves heavy steel billets into a hydraulic press bed, relying on the tie-rod-free extruded profile to sit flush against the machine guard without protruding hardware.
Selecting this 100 mm bore makes sense when an 80 mm cylinder (providing 2513 N push at 0.5 MPa) lacks the thrust for a rigid clamp or lift, but stepping up to a 125 mm bore (6136 N push) would be physically oversized. At 665 mm of travel, the 25 mm piston rod and M20x1.5 thread endure significant leverage; an external guide rail is strongly recommended to prevent rod-bearing bending under heavy lateral loads. Because the adjustable cushion only decelerates the piston near stroke end and provides no holding force, a BSE rod lock or external pilot-operated check valve is required if the load must remain stationary during a loss of air pressure. As a true ISO 15552 profile cylinder, it serves as a drop-in dimensional replacement for other ISO 15552 cylinders, utilizing the standard PT1/2 port and shared mounting accessories.
Quick checklist
At 0.5 MPa it generates 3927 N of push force and 3681 N of pull force. At 0.7 MPa the push force increases to 5497 N, with a maximum push capacity of 801 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
No. The field-adjustable air cushions at both ends only serve to decelerate the piston near the end of its stroke; they do not act as a brake. If you need to hold a vertical load without live air pressure, you must pair the cylinder with a BSE rod lock or an external pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.