The AirTAC AirTAC SE100X700S ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 700mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X700S is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty pneumatics. It delivers a robust 3927 N push force at 0.5 MPa, scaling to 5497 N at 0.7 MPa, making it ideal for high-load industrial actuation. The extruded aluminum barrel features a square design without external tie rods, yielding a compact, corrosion-resistant footprint that mounts flush against machine frames.
Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke verification. The field-adjustable pneumatic cushioning at both ends allows technicians to dial in deceleration to soften hard end stops during high-speed 30-800 mm/s cycles, protecting the 700 mm stroke from impact wear.
| Model | AirTAC SE100X700S ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 700 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×700 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 3927 N push at 0.5 MPa required to flatten and seal large corrugated packaging cartons over the 700 mm stroke.
Shifts heavy loaded pallets on a conveyor line using the 5497 N push force at 0.7 MPa, with the -S magnet confirming gate position.
Secures large injection molding tools with 801 kgf max force, utilizing the adjustable cushion to soften the long 700 mm travel stop.
Stepping down to the 80 mm bore yields 2513 N push at 0.5 MPa, while moving up to the 125 mm bore provides 6136 N—choose the SE100X700S when your mechanism requires approximately 400 kgf of thrust over a long 700 mm travel. As a standard ISO 15552 profile cylinder, it serves as a drop-in replacement for other ISO 15552 cylinders, sharing standard mounting hardware and PT1/2 porting. Because the stroke exceeds 300 mm, the 25 mm rod and internal bearing face increased bending moments under side loads; an external guide rail is recommended to prevent premature seal wear. Note that the air cushion only decelerates the piston near stroke end and will not hold a load if air pressure is lost.
Quick checklist
The SE100X700S generates 3927 N push and 3681 N pull at 0.5 MPa, 5497 N push at 0.7 MPa, and a maximum of 801 kgf at 1.0 MPa. Its operating speed ranges from 30-800 mm/s.
It is dimensionally interchangeable per ISO 15552, serving as a drop-in replacement sharing the same 100 mm mounting footprint and PT1/2 port. It does not hold its load without live air pressure; for position holding, use a BSE rod lock or external check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.