The AirTAC AirTAC SE100X700SH ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 700mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X700SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty actuation. It delivers a substantial 3927 N push force at 0.5 MPa (5497 N at 0.7 MPa), making it well-suited for high-load forming and heavy material handling tasks. The square extruded aluminum barrel eliminates external tie rods, yielding a flush profile that resists corrosion and simplifies fixture mounting in tight machinery envelopes.
Configured with a high-temperature FKM (Viton) seal, this unit operates reliably from 0 up to 150 degrees Celsius, accommodating hot environments where standard TPU seals would fail. The integrated magnet (-S) enables precise end-of-stroke detection using AirTAC CMSE reed or DMSE electronic sensors. Field-adjustable pneumatic cushioning at both ends allows you to tune deceleration and soften hard end stops, protecting long 700 mm strokes from damaging impact velocities.
| Model | AirTAC SE100X700SH ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 700 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×700 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the robust 5497 N push force at 0.7 MPa required to eject heavy plastic injection molds, while the FKM seal withstands ambient heat radiating from the mold platens.
Leverages the 700 mm stroke to push heavy pallets across transfer lines, using the field-adjustable cushion to bring the large mass to a smooth stop without shock.
Actuates heavy feed mechanisms near heated stamping presses, where the 150-degree Viton seal and flush no-tie-rod barrel profile prevent thermal degradation and simplify cleanup.
Selecting the SE100X700SH requires evaluating your force and stroke demands against its 3927 N push at 0.5 MPa. If your application needs less force, stepping down to the 80 mm bore yields 2513 N push, saving space and air consumption. Conversely, moving up to the 125 mm bore provides 6136 N push for heavier loads. Because this is a 700 mm stroke, the Ø25 mm rod and bearing must handle significant bending moments; an external guide rail is strongly recommended to prevent premature wear and side-load damage.
This cylinder serves as a dimensionally interchangeable drop-in replacement for any standard ISO 15552 cylinder, matching the 100 mm bore, 700 mm stroke, PT1/2 port, and standard mounting footprint. Remember that the adjustable air cushion only decelerates the piston near the end of travel; it does not hold a load. If your process requires position holding without live air pressure, integrate an external pilot-operated check valve or consider the AirTAC BSE rod-lock variant.
Quick checklist
The SE100X700SH provides a push force of 3927 N at 0.5 MPa and 5497 N at 0.7 MPa. The pull force is 3681 N at 0.5 MPa. The maximum push force is 801 kgf at 1.0 MPa. It operates at a speed range of 30-800 mm/s.
No, the adjustable air cushion only decelerates the piston near the end of stroke; it is not a locking mechanism. If the air supply is lost or the valve is centered, the piston will drift. For position holding without live pressure, use an external rod lock or pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.