The AirTAC AirTAC SE100X720S ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 720mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X720S is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty pneumatics. It delivers a substantial 3927 N push force at 0.5 MPa, scaling to 5497 N at 0.7 MPa, making it well-suited for high-load automation. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
Equipped with a built-in magnet (-S), this unit seamlessly integrates AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable pneumatic cushioning at both ends allows technicians to fine-tune end-cap deceleration via a dedicated screw, softening hard mechanical stops during high-velocity 720 mm strokes. Fluid compatibility is limited to filtered 40 µm air, operating safely between -20 and +70 C.
| Model | AirTAC SE100X720S ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 720 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×720 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Leverages the 3927 N push force at 0.5 MPa to reliably shove heavy timber pallets sideways onto secondary roller conveyors in packaging facilities.
Utilizes the 720 mm stroke to push deeply formed metal stampings completely out of hydraulic press dies, using the adjustable cushion to soften end-stop impact.
Applies the 5497 N extend force at 0.7 MPa to hold heavy steel chassis panels firmly in alignment while robotic spot-welding guns complete the frame.
When sizing this 100 mm bore actuator, evaluate stepping down to a 63 mm bore if your load requires less than 1559 N of push force at 0.5 MPa, or stepping up to a 125 mm bore for applications needing 6136 N. Because the 720 mm stroke generates significant leverage, long unsupported piston rods are prone to bending under side loads; always incorporate an external guide rail to prevent rod-bearing damage. As a dimensionally interchangeable ISO 15552 component, it serves as a drop-in replacement sharing standard mounting hardware, a PT1/2 port, and an M20x1.5 rod thread. Note that the adjustable air cushion only decelerates the piston near stroke end and does not hold loads; if the application must maintain position without live air pressure, specify a BSE series rod lock.
Quick checklist
This 100 mm bore cylinder provides 3927 N push and 3681 N pull at 0.5 MPa, 5497 N push at 0.7 MPa, and a maximum push force of 801 kgf at 1.0 MPa. It operates at speeds between 30-800 mm/s.
No, the SE100X720S is a standard double-acting cylinder and will drift if air is lost. The adjustable air cushion only decelerates the piston near the stroke ends; it does not lock the rod. For fail-safe load holding, use an AirTAC BSE series rod lock.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.