The AirTAC AirTAC SE100X730 ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 730mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X730SCBCR is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty automation. Operating at 0.5 MPa, it provides 3927 N of push force and 3681 N of pull force, scaling to a maximum output of 801 kgf at 1.0 MPa. The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while maintaining standardized ISO 15552 dimensions.
This specific configuration includes a built-in magnet for CMSE reed and DMSE electronic position sensing, paired with a CB double clevis mounting style for pivoting articulation. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts when cycling 730 mm strokes at speeds up to 800 mm/s.
| Model | AirTAC SE100X730 ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 730 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×730 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Leverages the 3927 N push force at 0.5 MPa to positively strip and eject empty wooden pallets from a magazine stack, utilizing the CB clevis to accommodate angular pivot motion.
Shifts heavy injection molding platens along the 730 mm stroke, relying on the -S magnet and DMSE electronic sensors to confirm mold open/close positioning for robotic extractors.
Actuates large forming press loading doors, where the 801 kgf maximum thrust capacity overcomes heavy mechanical resistance and the adjustable cushions absorb kinetic energy at stroke ends.
Selecting this 100 mm bore cylinder is appropriate when applications require substantial thrust, such as the 5497 N generated at 0.7 MPa. If a design demands less force, stepping down to the 80 mm bore yields 2513 N of push at 0.5 MPa, whereas scaling up to the 125 mm bore provides 6136 N for heavier payloads. Because the 730 mm stroke exceeds 300 mm, the unsupported piston rod is susceptible to bending under lateral loads; integrating an external guide rail prevents side-load damage to the rod bearing and seal.
As a dimensionally interchangeable ISO 15552 component, this cylinder serves as a direct drop-in replacement for other 100 mm bore, 730 mm stroke profile cylinders with PT1/2 ports. Note that the adjustable air cushion only decelerates the piston near the stroke ends and does not function as a locking device; if the machinery must hold a vertical load without live air pressure, an external pilot-operated check valve or a dedicated BSE rod lock variant is required.
Quick checklist
At 0.5 MPa, this 100 mm bore cylinder generates 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force increases to 5497 N, and the maximum rated push is 801 kgf at 1.0 MPa. The standard operating speed range is 30-800 mm/s.
Yes, the SE100X730SCBCR is dimensionally interchangeable per ISO 15552 standards. It shares the same 100 mm bore, 730 mm stroke, PT1/2 port, and mounting footprint as other ISO 15552 profile cylinders, allowing it to serve as a drop-in replacement for shared mounting hardware without requiring machine modifications.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.