The AirTAC AirTAC SE100X750S ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 750mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X750S is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty automation. Operating at 0.5 MPa, it generates 3927 N of push force and 3681 N of pull force, scaling to a maximum of 801 kgf at 1.0 MPa. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing standardized ISO 15552 interface dimensions for seamless retrofitting.
This 100 mm bore unit features a 750 mm stroke and a built-in magnet (-S) for position sensing with CMSE reed or DMSE electronic switches. Field-adjustable pneumatic cushioning at both ends allows technicians to dial in end-of-stroke deceleration via a screw, softening hard mechanical stops during high-velocity 30-800 mm/s cycles.
| Model | AirTAC SE100X750S ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 750 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×750 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 3927 N push force required to index heavy timber pallets across a 750 mm transfer station during high-speed packaging line operations.
Utilizes the 750 mm stroke and DMSE electronic sensor magnet to reach deep into injection molding machines for positive ejection of large plastic parts.
Drives a heavy protective welding shield with 801 kgf maximum force capacity, relying on adjustable end cushions to absorb kinetic energy at 800 mm/s.
Selecting the SE100X750S is appropriate when your application requires substantial thrust over a long reach. If 3927 N of push at 0.5 MPa is excessive, stepping down to the 80 mm bore yields 2513 N, whereas moving up to the 125 mm bore provides 6136 N for heavier payloads. Because this is a standard 750 mm stroke within the 100 mm bore's 1500 mm maximum, it is readily available.
For strokes of 300 mm or more, the unsupported mass of the 25 mm rod increases the risk of rod-bearing bending under side loads; integrating an external linear guide is strongly recommended to prevent premature seal wear. Furthermore, the adjustable air cushion only decelerates the piston near the stroke ends and does not lock the load—if air pressure drops, the cylinder will drift, requiring a BSE rod lock for fail-safe holding.
Quick checklist
At 0.5 MPa, the SE100X750S delivers 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force is 5497 N. The maximum push force is 801 kgf when operating at the 1.0 MPa pressure limit.
Yes, the SE100X750S is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. You can drop it into existing foot or flange mounting hardware, but note this specific unit uses a PT1/2 port and includes a built-in magnet for CMSE and DMSE sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.