The AirTAC AirTAC SE100X800S ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 800mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X800S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 3927 N push force at 0.5 MPa. Its extruded aluminum barrel omits external tie rods, yielding a compact, flush-mounting body that resists corrosion and simplifies sensor placement along three integrated grooves. Equipped with a built-in magnet, this unit interfaces directly with AirTAC CMSE reed and DMSE electronic position switches.
Driving an 800 mm stroke requires precise end-of-travel management, so this cylinder incorporates field-adjustable pneumatic cushioning at both ends. Technicians can tune the cushion screws to decelerate the 25 mm hard-chrome rod smoothly, preventing harsh mechanical impacts at high cycling speeds up to 800 mm/s.
| Model | AirTAC SE100X800S ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 800 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×800 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Pushes heavy loaded pallets between roller conveyor sections using its 3927 N push force across the full 800 mm stroke.
Extends 800 mm to sweep large corrugated carton flaps into position for hot-melt gluing, using adjustable cushioning to prevent crushing.
Acts as a long-reach extraction arm pulling molded parts from deep injection machinery, relying on 3681 N pull force and DMSE sensors.
Selecting the SE100X800S provides 3927 N of push at 0.5 MPa. If your application requires less force, stepping down to the 80 mm bore yields 2513 N; conversely, moving up to the 125 mm bore provides 6136 N. Because this unit features an 800 mm stroke, the extended rod is highly susceptible to side-load bending—always pair it with an external guide rail to prevent premature rod-bearing wear. As a standard ISO 15552 profile cylinder, it serves as a drop-in replacement for any matching 100 mm bore and 800 mm stroke footprint, utilizing standard PT1/2 ports and an -S magnet for position sensing.
Quick checklist
At 0.5 MPa, this 100 mm bore cylinder provides 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force increases to 5497 N, with a maximum push capacity of 801 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
No, the adjustable air cushion only decelerates the piston near the end of stroke; it does not act as a brake. If your application must hold a load without live air pressure, you must use an external rod lock like the BSE series or a pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.