The AirTAC AirTAC SE100X800SFA ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 800mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X800SFA is a double-acting single-rod profile cylinder built to ISO 15552 standards, delivering a robust 3927 N push force at 0.5 MPa. Equipped with an FA front flange and a built-in position magnet, it utilizes a PT1/2 port and a Ø25 mm piston rod to drive heavy loads over its 800 mm stroke. The extruded aluminum barrel omits external tie rods, yielding a smooth, corrosion-resistant body that mounts flush against machine frames.
Because this model carries the -S magnet code, it directly supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable pneumatic cushioning at both ends allows technicians to tune the deceleration of the massive 801 kgf maximum payload, preventing harsh end-stop impacts without relying on fixed rubber bumpers.
| Model | AirTAC SE100X800SFA ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 800 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×800 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives a 100-tonne stamping die over 800 mm, utilizing the 5497 N push force at 0.7 MPa to form thick-gauge steel brackets without deflecting.
Pushes fully loaded 500 kg shipping pallets off a high-speed conveyor belt, relying on the FA flange to absorb the severe lateral shear during redirection.
Actuates an 800 mm extraction arm in an AS/RS crane, using the built-in magnet and DMSE sensors to confirm tote retrieval at extreme vertical heights.
Selecting the SE100X800SFA makes sense when your application requires substantial thrust over a long reach. If you need to step the bore down, the 80 mm variant provides 2513 N of push at 0.5 MPa; stepping up to the 125 mm bore yields 6136 N. This 100 mm bore achieves 5497 N of push at 0.7 MPa, making it ideal for high-force pressing and heavy lifting tasks.
At 800 mm of stroke, the Ø25 mm rod and internal bearing face significant bending moments under side loads—an external guide rail is strongly recommended to prevent premature seal wear. The FA front flange provides a rigid forward mounting face for straight-line thrust, while the PT1/2 ports ensure high airflow for rapid cycling at speeds up to 800 mm/s. Note that the adjustable air cushion only decelerates the piston near stroke end; it cannot hold a load if air pressure drops, so a BSE rod lock is required for fail-safe positioning.
Quick checklist
At 0.5 MPa, this 100 mm bore cylinder provides 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force increases to 5497 N. The maximum rated push force is 801 kgf when operated at the 1.0 MPa pressure limit.
Yes, the SE100X800SFA is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting footprint and front flange interface as competing ISO 15552 profile cylinders. You can drop it into existing machinery without modifying the mounting plate.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.