The AirTAC AirTAC SE100X80SH ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 80mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X80SH is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty pneumatics. It delivers a substantial 3927 N push force at 0.5 MPa (801 kgf maximum at 1.0 MPa) across its 80 mm stroke. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames without protruding hardware.
This specific configuration includes an -S magnet for non-contact position sensing via AirTAC CMSE reed or DMSE electronic switches seated in the triple-sided sensor groove. Equipped with high-temperature FKM (Viton) seals, the operating range extends to 150 C, making it highly resilient in thermally aggressive environments. The field-adjustable pneumatic cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration via a set screw, softening hard mechanical impacts during high-speed cycling.
| Model | AirTAC SE100X80SH ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 80 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 3927 N push force required to eject dense plastic parts from an injection molding die, utilizing the FKM seal to withstand ambient mold heat up to 150 C.
Cycles heavy wooden pallets into a packaging line, relying on the 80 mm stroke and robust 25 mm rod to absorb high initial impact without bending.
Advances thick-gauge steel strip into a mechanical stamping press, using the field-adjustable cushions to soften the abrupt stops inherent to 30-800 mm/s feed rates.
Generating 3927 N of thrust at 0.5 MPa, this 100 mm bore cylinder fits demanding load requirements. If your application requires less force, the 80 mm bore variant provides 2513 N of push at 0.5 MPa, whereas scaling up to the 125 mm bore yields 6136 N at the same pressure. Because the 80 mm stroke keeps the unsupported rod length short, side-load stress on the M20x1.5 rod thread and bearing remains minimal, though heavy lateral loads still necessitate an external guide. As a dimensionally interchangeable ISO 15552 component, it serves as a direct drop-in replacement for other ISO 15552 profile cylinders, utilizing the existing PT1/2 port and standardized mounting hardware. Note that the adjustable air cushions only decelerate the piston near stroke end; they cannot hold a load if air pressure is lost.
Quick checklist
The SE100X80SH generates 3927 N push and 3681 N pull at 0.5 MPa, 5497 N push at 0.7 MPa, and a maximum of 801 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the H seal option specifies FKM (Viton) elastomers, extending the operating temperature range up to 150 C. However, the adjustable air cushions only decelerate the piston near the stroke ends; they do not lock or hold a load if air pressure drops.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.