The AirTAC AirTAC SE100X850 ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 850mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X850 is a double-acting single-rod ISO 15552 profile cylinder engineered for substantial actuation tasks, delivering a robust 3927 N push force at 0.5 MPa and up to 801 kgf at 1.0 MPa. Because this unit lacks the -S magnet code, it is built for pure drive power without position sensing out of the box.
Its extruded aluminum barrel omits external tie rods entirely, yielding a flush, corrosion-resistant body that simplifies mounting and reduces debris buildup. The field-adjustable pneumatic cushioning at both ends allows technicians to dial in end-of-stroke deceleration, softening hard impacts when moving heavy masses at speed.
| Model | AirTAC SE100X850 ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 850 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×850 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the heavy sealing head of an automated pallet strapper, utilizing the 3927 N push at 0.5 MPa to tension and seal steel straps around heavy freight loads.
Pushes raw timber logs off a primary conveyor line, relying on the 850 mm stroke and field-adjustable cushioning to decelerate massive wood payloads safely.
Feeds heavy gauge sheet metal blanks into a large press brake, where the flush extruded profile allows tight side-by-side mounting without tie-rod interference.
With an 850 mm stroke exceeding the 1500 mm standard maximum, this bore is a made-to-order configuration. When sizing, note the 80 mm bore provides 2513 N push at 0.5 MPa, while the 125 mm bore yields 6136 N push. If the application requires holding this load vertically without air pressure, a plain SE will drift; specify a BSE rod lock variant instead.
For an 850 mm stroke, the unsupported piston rod (Ø25 mm, M20x1.5 thread) is highly susceptible to bending under side loads. An external guide rail is strongly recommended to prevent premature rod-bearing wear. As a dimensionally interchangeable ISO 15552 cylinder, it serves as a drop-in retrofit for existing 100 mm bore PT1/2 ported setups.
Quick checklist
This 100 mm bore cylinder achieves a push force of 3927 N and a pull force of 3681 N at 0.5 MPa. At 0.7 MPa, the push force is 5497 N, with a maximum push of 801 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE100X850 is dimensionally interchangeable per ISO 15552 standards, serving as a drop-in replacement for other 100 mm bore profile cylinders. It uses a PT1/2 port and M20x1.5 rod thread, but note this specific SKU lacks the -S magnet for CMSE or DMSE position sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.