The AirTAC AirTAC SE100X850S ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 850mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X850SFTC is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty motion. It delivers a substantial 3927 N push force at 0.5 MPa, utilizing a 100 mm bore and an 850 mm stroke to power demanding equipment. The extruded aluminum barrel lacks external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
Equipped with a built-in magnet (-S), this unit seamlessly interfaces with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable air cushion at both ends allows technicians to dial in end-stop deceleration via a set screw, softening impacts during high-speed 30-800 mm/s cycles. Because the 850 mm stroke exceeds the standard 1500 mm maximum, this is a made-to-order configuration.
| Model | AirTAC SE100X850S ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 850 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×850 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives a 3927 N welding fixture over 850 mm to position heavy chassis panels, relying on the FTC trunnion to accommodate pivot arc during the stroke.
Pushes heavy pallets off a high-speed line using 5497 N at 0.7 MPa, with the adjustable cushion absorbing kinetic energy at the 850 mm end-stop.
Reaches deep into an injection molding machine to extract 100 mm parts, using the built-in magnet and DMSE sensor to confirm safe part removal.
When sizing this actuator, consider stepping down to the 80 mm bore if your load requires less than 2513 N of push at 0.5 MPa, or move up to the 125 mm bore for 6136 N of thrust. This FTC (center trunnion) mount handles pivoting loads, but an 850 mm stroke generates significant bending moments on the rod bearing; an external guide is strongly recommended to prevent premature wear. As a standard ISO 15552 profile cylinder, it serves as a drop-in dimensional replacement for other ISO 15552 cylinders, sharing standard mounting hardware and a PT1/2 port. Note that the adjustable cushion only decelerates the piston near stroke end—it is not a lock; if the application must hold a vertical load without live pressure, use a BSE rod lock.
Quick checklist
At 0.5 MPa, this 100 mm bore cylinder provides 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force reaches 5497 N, with a maximum push capacity of 801 kgf at 1.0 MPa. It operates at speeds of 30-800 mm/s.
Yes. The SE100X850SFTC is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. Its extruded profile barrel and FTC mounting dimensions match the standard footprint, allowing a direct drop-in replacement for other ISO 15552 cylinders without modifying the machine frame.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.