The AirTAC AirTAC SE100X880S ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 880mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X880S is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty automation. It delivers a substantial 3927 N push at 0.5 MPa, utilizing a 25 mm rod and a PT1/2 port to drive high-inertia loads. The 880 mm stroke is a made-to-order length exceeding the 1500 mm standard maximum, tailored specifically for long-travel machinery.
Its square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against frames. Equipped with a built-in magnet (-S), this unit seamlessly integrates AirTAC CMSE reed or DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable air cushioning at both ends allows technicians to tune deceleration via a set screw, softening hard impacts at high cycle speeds.
| Model | AirTAC SE100X880S ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 880 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×880 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives a heavy-duty pallet transfer carriage over an 880 mm stroke, utilizing the 3927 N push force to shift loaded skids between packaging zones.
Ejects formed metal parts from a hydraulic press, using the 36 mm adjustable cushion to absorb the high kinetic energy generated during rapid retraction.
Actuates a heavy corrugated carton forming arm, relying on the -S magnet and DMSE sensors to verify full extension before adhesive application.
Selecting this 100 mm bore makes sense when 80 mm falls short—yielding 2513 N push at 0.5 MPa—or when you want to avoid stepping up to the massive 125 mm bore that generates 6136 N. Because this cylinder uses a double-acting air circuit, it cannot hold a load if air pressure drops or the valve centers; the piston will drift. For gravity-loaded vertical applications requiring static holding, pair this cylinder with an external pilot-operated check valve or explore the BSE rod-lock variant.
At 880 mm of travel, the unsupported mass of the piston and rod introduces significant side-load risks that can accelerate rod-bearing wear. Implementing an external linear guide is strongly recommended to prevent bending and premature seal failure. As a true ISO 15552 profile cylinder, it provides a drop-in dimensional retrofit for competing standard cylinders, utilizing standard mounting accessories like FA or TC brackets alongside its PT1/2 port and M20x1.5 rod thread.
Quick checklist
At 0.5 MPa, this 100 mm bore cylinder provides 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force increases to 5497 N. The maximum push force is 801 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes. The SE100X880S is dimensionally interchangeable per ISO 15552 standards. You can use your existing mounting hardware and drop it directly into machinery designed for other ISO 15552 profile cylinders, maintaining the same PT1/2 port and M20x1.5 rod thread locations.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.