The AirTAC AirTAC SE100X900SH ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 900mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X900SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty linear motion. It delivers a robust 3927 N push force at 0.5 MPa and features a 900 mm stroke. Equipped with a Viton (FKM) seal, this unit reliably operates in extreme thermal environments up to 150 C. A built-in magnet (-S) enables seamless integration with CMSE reed and DMSE electronic position sensors.
Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush in tight spaces. The field-adjustable air cushioning at both ends allows precise deceleration tuning to mitigate hard end-stop impacts at high cycle speeds. Because it adheres to the ISO 15552 dimensional standard, it serves as a direct, drop-in replacement for comparable profile cylinders without requiring custom mounting plates.
| Model | AirTAC SE100X900SH ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 900 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×900 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives long-stroke ejector pins in hot mold environments where the 150 C FKM seal survives ambient heat and the 3927 N push force clears heavy parts.
Moves large body panels between stamping stations, utilizing the 900 mm stroke and 801 kgf max force to traverse wide press beds.
Actuates heavy pallet routing gates where the ISO 15552 footprint allows easy retrofitting and the no-tie-rod profile resists shop debris.
This 100 mm bore cylinder provides a maximum push of 801 kgf at 1.0 MPa. If your application requires less force, stepping down to an 80 mm bore drops the 0.5 MPa push to 2513 N. Conversely, scaling up to a 125 mm bore increases the 0.5 MPa push to 6136 N. Note that a plain SE cylinder drifts when air is lost or a valve centers; if your process demands fail-safe load holding, specify a BSE rod lock variant or use an external pilot-operated check valve.
At a 900 mm stroke, the unsupported piston rod is highly susceptible to side-load bending and rod-bearing wear. To prevent premature seal failure and uneven tracking, incorporate an external linear guide to support the load. This model features a PT1/2 port, a 25 mm rod with an M20x1.5 thread, and the high-temperature FKM seal.
Quick checklist
At 0.5 MPa, this 100 mm bore cylinder provides 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force is 5497 N, with a maximum push of 801 kgf at 1.0 MPa. It operates at speeds of 30-800 mm/s and utilizes a high-temperature FKM seal rated for 150 C.
No, the adjustable air cushion at both ends only decelerates the piston near the stroke end; it is not a mechanical lock. A standard SE cylinder will drift if air is lost or the valve is centered. For fail-safe load holding, use a BSE rod lock variant or an external pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.