The AirTAC AirTAC SE100X90H ISO 15552 Cylinder | 100mm Viton is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 90mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X90H is a double-acting single-rod ISO 15552 profile cylinder engineered for high-temperature automation. Equipped with a Viton (FKM) seal, it operates reliably in environments up to 150 C, far exceeding the 70 C limit of standard elastomers. Delivering a robust 3927 N push force at 0.5 MPa, this 100 mm bore unit is built to move heavy loads through a 90 mm stroke.
Its extruded aluminum barrel eliminates external tie rods, presenting a smooth, corrosion-resistant profile that mounts flush against machine frames. The field-adjustable pneumatic cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration, protecting tooling from impact damage. Note that this specific SKU omits the internal magnet, so it cannot host CMSE or DMSE position sensors without modification.
| Model | AirTAC SE100X90H ISO 15552 Cylinder | 100mm Viton |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 90 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Withstands ambient heat near molding presses to deliver 3927 N of ejection force, utilizing the Viton seal to prevent thermal degradation.
Pushes heavy metal blanks into heated dies, where the 150 C FKM seal survives radiant heat that would destroy standard NBR or TPU packings.
Acts as a heavy-duty 90 mm stroke stop gate for inbound pallets, using adjustable cushioning to absorb the 3681 N retract impact smoothly.
Selecting this 100 mm bore cylinder makes sense when your application requires substantial thrust between the 63 mm class (1559 N push @0.5 MPa) and the massive 125 mm class (6136 N push @0.5 MPa). The integrated Viton seal is the deciding factor here: if your environment only reaches 70 C, the standard TPU SE100X90 saves cost, but for 150 C thermal exposure, this H-seal variant is mandatory. Keep in mind that a standard SE cylinder does not hold position if air pressure drops; for fail-safe load holding, you must specify a BSE rod-lock variant or use an external pilot-operated check valve.
For a drop-in retrofit, verify that the existing machine uses an ISO 15552 mounting interface, a PT1/2 port, and an M20x1.5 rod thread. This 90 mm stroke falls under the 300 mm threshold, so standard rod-bearing bending is minimal, though heavy side loads should still utilize an external guide rail to prevent premature seal wear.
Quick checklist
At 0.5 MPa, the push force is 3927 N and the pull force is 3681 N. At 0.7 MPa, the push force reaches 5497 N. The maximum push force is 801 kgf at 1.0 MPa.
Yes, the SE100X90H is dimensionally interchangeable per ISO 15552 standards. You can drop it in as a replacement for other ISO 15552 profile cylinders, provided your porting matches the PT1/2 thread and the M20x1.5 rod end.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.