The AirTAC AirTAC SE100X95 ISO 15552 Cylinder | 100mm Bore is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø100mm bore and 95mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
The AirTAC SE100X95 is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty automation. It delivers a robust 3927 N push force at 0.5 MPa, making it ideal for high-thrust linear motion tasks.
Built with a square extruded aluminum barrel free of external tie rods, this design offers a flush, corrosion-resistant mounting surface that simplifies bracket alignment. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration, protecting machinery from hard impacts. Note that this specific SKU is configured without a position-sensing magnet.
| Model | AirTAC SE100X95 ISO 15552 Cylinder | 100mm Bore |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 95 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3682 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 100 | Bore size in mm. |
| ×95 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Generates 5497 N of thrust at 0.7 MPa to secure heavy injection mold halves during the pressing cycle.
Provides the robust physical stroke needed to push fully loaded pallets onto secondary packaging lines.
Delivers consistent 3927 N force at 0.5 MPa to seat large bearings into automotive transmission housings.
When sizing this 100 mm bore actuator, compare its 3927 N push at 0.5 MPa against the 80 mm option (2513 N) for lighter loads, or the 125 mm option (6136 N) if your application requires maximum thrust. As a dimensionally interchangeable ISO 15552 unit, it serves as a direct drop-in replacement for other standard profile cylinders, matching the PT1/2 port, 95 mm stroke, and standard mounting accessories without machining. Remember that the adjustable air cushion only decelerates the piston near stroke end; it cannot hold a load if air pressure is lost, so a BSE rod lock is required for fail-safe positioning.
Quick checklist
At 0.5 MPa, the SE100X95 provides 3927 N of push force and 3681 N of pull force. At 0.7 MPa, the push force increases to 5497 N. The maximum rated push force is 801 kgf at 1.0 MPa.
This specific SE100X95 SKU is manufactured without a built-in magnet, meaning it will not trigger AirTAC CMSE or DMSE position sensors. If electronic or reed switch feedback is required, you must specify an SE model with the -S magnet option.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.