Airtac SE125 Standard Cylinder SE125X1060
The AirTAC Airtac SE125 Standard Cylinder SE125X1060 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø125mm bore and 1060mm stroke, PT1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ125 mm
- Stroke1060 mm
- Port sizePT1/2
- Acting typeDouble acting
- Rod threadM27×2
- CushionAdjustable, 40 mm
About the Airtac SE125 Standard Cylinder SE125X1060
The AirTAC SE125X1060 is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty pneumatics, delivering a substantial 6136 N push force at 0.5 MPa. Because the 1060 mm stroke exceeds the standard 1500 mm maximum for this bore, this specific SKU is a non-standard, made-to-order unit built to exacting dimensional tolerances. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant profile that mounts flush into tight machine frames.
This unit features a PT1/2 port, a robust Ø32 mm piston rod with an M27x2 thread, and field-adjustable air cushioning at both ends to decelerate the massive 1252 kgf maximum load smoothly. Note that this specific configuration lacks the -S magnet option, meaning it is not equipped for AirTAC CMSE or DMSE position sensing out of the box.
Airtac SE125 Standard Cylinder SE125X1060 Technical Specifications
| Model | Airtac SE125 Standard Cylinder SE125X1060 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø125 mm |
| Stroke | 1060 mm |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M27×2 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 40 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø125mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 6136 N | 5734 N |
| 0.7 MPa | 8590 N | — |
| Max (@1.0 MPa) | 1251 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE125 Standard Cylinder SE125X1060
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 125 | Bore size in mm. |
| ×1060 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE125 Standard Cylinder SE125X1060 Is Used
Automotive Tier-1 Press Ejection
Provides the 8590 N push at 0.7 MPa required to eject heavy stamped body panels from a 1000-ton servo press, utilizing the 1060 mm stroke to fully clear the die area.
Palletizer Main Lift Arm
Drives the vertical lifting mast of a high-speed robotic palletizer, where the 1060 mm stroke accommodates varying pallet heights and the 1252 kgf capacity handles heavy goods.
Heavy Steel Plate Bending
Acts as the primary pneumatic actuator in a thick steel plate bending fixture, using its 6136 N base push force and M27x2 rod thread to drive the forming tooling reliably.
Is the Airtac SE125 Standard Cylinder SE125X1060 the Right Cylinder?
Selecting this bore ensures you achieve the full 6136 N push at 0.5 MPa (8590 N at 0.7 MPa). If your application requires slightly less force, stepping down to the 100 mm bore yields 3927 N push at 0.5 MPa; however, there is no larger standard bore above 125 mm in the SE series. Because this is a non-standard 1060 mm stroke, expect a made-to-order lead time.
For strokes of 300 mm or more, the extended length of the Ø32 mm rod creates a high risk of rod-bearing bending under side loads. You must use an external guide to prevent premature seal failure. Additionally, the adjustable air cushion only decelerates the piston near the stroke ends; it is not a lock. If the machine must hold a load vertically or without live air pressure, install a BSE rod lock or an external pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE125 Standard Cylinder SE125X1060 FAQ
This 125 mm bore cylinder provides a push force of 6136 N and a pull force of 5734 N at 0.5 MPa. At 0.7 MPa, the push force is 8590 N, with a maximum push capacity of 1252 kgf at 1.0 MPa. It uses a PT1/2 port and operates at speeds of 30-500 mm/s.
Yes, the SE125X1060 is dimensionally interchangeable with other ISO 15552 profile cylinders, allowing you to drop it into existing footprints and use standard FA, FB, or TC mounting hardware. This specific SKU lacks the -S magnet option, so it does not support AirTAC CMSE or DMSE position sensors unless the magnet is specified.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE125 Standard Cylinder SE125X1060
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.