Airtac SE32 Standard Cylinder SE32X100FTC
The AirTAC Airtac SE32 Standard Cylinder SE32X100FTC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 100mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke100 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X100FTC
The AirTAC SE32X100FTC is a double-acting single-rod ISO 15552 profile cylinder engineered for compact pneumatics. Delivering 402 N of push force at 0.5 MPa, it features a 32 mm bore and 100 mm stroke. The extruded aluminum barrel omits external tie rods, yielding a smooth, corrosion-resistant body that mounts flush into tight machine envelopes while maintaining the standardized ISO 15552 footprint.
This FTC-mounted unit incorporates field-adjustable pneumatic cushioning at both ends, allowing technicians to tune end-of-stroke deceleration via a set screw rather than relying on a fixed bumper. It operates without a built-in magnet, meaning external position sensing is not supported on this specific SKU. For tasks requiring positive load holding upon air loss, this cylinder must be paired with an external rod lock or pilot-operated check valve, as the cushion only decelerates the piston.
Airtac SE32 Standard Cylinder SE32X100FTC Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X100FTC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X100FTC
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X100FTC Is Used
PCB Depaneling Router Gates
Actuates routing machine access gates, utilizing the 402 N push force to secure panels during board separation.
Lab Sample Dispenser
Drives a 100 mm stroke to position pipette arrays over microplates, benefiting from the smooth no-tie-rod profile that prevents reagent buildup.
Carton Flap Folder
Folds small corrugated carton flaps at 30-800 mm/s, relying on the adjustable end cushions to prevent hard impacts on the folding arms.
Is the Airtac SE32 Standard Cylinder SE32X100FTC the Right Cylinder?
Choosing this 32 mm bore depends on your force requirements; it provides 402 N push at 0.5 MPa. If your application demands less force, step down to the 25 mm bore (if available) or a smaller series, but if you need 628 N push at 0.5 MPa, step up to the 40 mm bore. The 100 mm stroke is standard and integrates seamlessly with the FTC mounting accessory. Because this SKU lacks the -S magnet, it cannot host CMSE or DMSE sensors; if position feedback is required, select the -S variant. Remember, a plain SE cylinder drifts when air is lost, so do not rely on it for static load holding.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X100FTC FAQ
The SE32X100FTC provides 402 N push and 345 N pull at 0.5 MPa, 563 N push at 0.7 MPa, and a maximum push of 82 kgf at 1.0 MPa. It operates at speeds between 30 and 800 mm/s.
Yes, it is dimensionally interchangeable per ISO 15552 and uses a standard FTC mounting interface. The PT1/8 port and M10x1.25 rod thread match standard hardware, though it lacks a sensor magnet for position feedback.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X100FTC
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.