Airtac SE32 Standard Cylinder SE32X105S
The AirTAC Airtac SE32 Standard Cylinder SE32X105S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 105mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke105 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X105S
The AirTAC SE32X105S is a double-acting single-rod ISO 15552 profile cylinder engineered for compact pneumatics. Delivering 402 N of push force at 0.5 MPa, it uses a 12 mm hard-chrome rod with an M10x1.25 thread. The square extruded aluminum barrel omits external tie rods, yielding a flush body that resists corrosion and simplifies mounting in tight machine layouts.
Equipped with a built-in magnet (-S), this unit directly interfaces with AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. Field-adjustable air cushions at both ends allow you to tune end-stop deceleration, absorbing kinetic energy smoothly rather than relying on a fixed rubber bumper.
Airtac SE32 Standard Cylinder SE32X105S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X105S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 105 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X105S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×105 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X105S Is Used
PCB Panel Drilling
Drives small precision drill spindles in PCB routing machines, utilizing the 105 mm stroke and 402 N push force to plunge through fiberglass substrates cleanly.
Lab Dispense Heads
Actuates pneumatic liquid dispense valves in analytical lab equipment, relying on the built-in magnet to trigger DMSE electronic sensors for exact shot dosing.
Carton Flap Folders
Folds minor flaps on small pharmaceutical cartons, where the compact 32 mm profile barrel fits neatly between narrow conveyor guide rails.
Is the Airtac SE32 Standard Cylinder SE32X105S the Right Cylinder?
Stepping up to the 40 mm bore provides 628 N of push at 0.5 MPa if your 105 mm stroke needs greater thrust, while no smaller standard SE bore exists below 32 mm. Remember that a plain SE cylinder will drift if air pressure is lost or the valve centers; for safety holding of vertical loads, consider the BSE rod lock variant. Because the stroke is 105 mm, side-load bending on the 12 mm rod bearing is minimal, but always verify rod-end thread alignment.
As a true ISO 15552 cylinder, the SE32X105S is dimensionally interchangeable with other ISO 15552 profile cylinders, allowing you to reuse existing mounting brackets and PT1/8 port plumbing during retrofits.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X105S FAQ
The SE32X105S provides 402 N push and 345 N pull at 0.5 MPa, 563 N push at 0.7 MPa, and a maximum push of 82 kgf at 1.0 MPa. It features a 12 mm rod with an M10x1.25 thread and a PT1/8 port.
Yes, the SE32X105S is dimensionally interchangeable per ISO 15552 standards. You can drop it directly into existing mounting hardware, and the -S magnet works seamlessly with AirTAC CMSE and DMSE position sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X105S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.