Airtac SE32 Standard Cylinder SE32X460S
The AirTAC Airtac SE32 Standard Cylinder SE32X460S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 460mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke460 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X460S
The AirTAC SE32X460S is a double-acting single-rod ISO 15552 profile cylinder, delivering 402 N of push force at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant body that mounts cleanly against machine frames. The integrated -S magnet directly interfaces with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection.
Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts at operating speeds up to 800 mm/s. This 460 mm stroke configuration relies on a 12 mm rod with an M10x1.25 thread, providing a robust interface for standard tooling plates.
Airtac SE32 Standard Cylinder SE32X460S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X460S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 460 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X460S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×460 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X460S Is Used
PCB Router Z-Axis Lift
Drives a light-duty 460 mm vertical lift for a printed circuit board routing spindle, using the 402 N push force to elevate the cutting head while relying on DMSE sensors for position feedback.
Film Roll Tensioning Arm
Actuates a 460 mm travel tensioning arm on a packaging line, where the compact no-tie-rod profile prevents snagging on moving web materials.
Lab Sample Dispenser
Extends 460 mm to position a fluid nozzle over a multi-well plate, utilizing the adjustable end cushions to gently stop the 12 mm rod without disturbing delicate samples.
Is the Airtac SE32 Standard Cylinder SE32X460S the Right Cylinder?
Select this 32 mm bore when your application requires the 402 N push at 0.5 MPa; if you need less force, step down is not available as this is the smallest size, but if you need substantially more power, the 40 mm bore yields 628 N push. Because the 460 mm stroke is relatively long for this small bore, the 12 mm rod and rod-bearing interface face bending stresses under side loads—an external guide rail is strongly recommended to prevent premature wear.
This cylinder is dimensionally interchangeable per ISO 15552, serving as a drop-in replacement for other ISO 15552 cylinders without altering mounting footprints. It uses a PT1/8 port, standard 460 mm stroke, basic mounting, and a built-in magnet for CMSE / DMSE sensors. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not hold a load if air pressure is lost.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X460S FAQ
The SE32X460S provides 402 N push and 345 N pull at 0.5 MPa, 563 N push at 0.7 MPa, and a maximum push of 82 kgf at 1.0 MPa. It has a standard 460 mm stroke and operates at speeds of 30-800 mm/s.
It is dimensionally interchangeable per ISO 15552, allowing a drop-in retrofit for other ISO 15552 cylinders. However, it does not hold position if air is lost; the adjustable air cushion only decelerates the piston near the end of stroke and is not a locking mechanism.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X460S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.