Airtac SE32 Standard Cylinder SE32X910S
The AirTAC Airtac SE32 Standard Cylinder SE32X910S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 910mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke910 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X910S
The AirTAC SE32X910S is a double-acting, single-rod ISO 15552 profile cylinder engineered for a 910 mm stroke. It delivers 402 N of push force and 345 N of pull force at 0.5 MPa, utilizing a 12 mm rod and an M10x1.25 thread. Because 910 mm exceeds the standard 1000 mm limit for this bore family, this specific 910 mm travel length is classified as a non-standard, made-to-order stroke.
The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts during high-speed cycling. Equipped with a built-in magnet (-S), it supports direct mounting of CMSE reed and DMSE electronic sensors along the three integrated sensor grooves.
Airtac SE32 Standard Cylinder SE32X910S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X910S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 910 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X910S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×910 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X910S Is Used
Packaging Line Carton Diverter
Uses the 910 mm stroke to push corrugated cartons across a wide packaging conveyor belt, relying on the 402 N push force to overcome side friction.
Laboratory Sample Tray Shuttle
Transfers sample trays between testing stations, utilizing the built-in magnet with DMSE electronic sensors for precise position verification at extended reach.
Textile Loom Thread Guide
Actuates a thread guiding mechanism over a 910 mm span, benefiting from the tie-rod-free extruded profile to mount flush within tight machinery clearances.
Is the Airtac SE32 Standard Cylinder SE32X910S the Right Cylinder?
If 402 N of push at 0.5 MPa is too much for your payload, step down to the 32 mm bore's nearest neighbor, the SE40, which actually provides 628 N. If you need less force, a smaller bore would be required, though 32 mm is the smallest standard SE size available. Because the stroke is 910 mm, the unsupported piston rod is highly susceptible to bending under side loads; an external guide bearing is strongly recommended to prevent premature seal failure and rod bearing wear.
As a standard ISO 15552 cylinder, the SE32X910S is dimensionally interchangeable with other ISO 15552 profile cylinders, allowing direct retrofitting using existing mounting hardware. Note that a plain SE cylinder does not hold its position when air is lost or the valve is centered; the piston will drift. For load-holding requirements, consider the BSE rod lock variant. This unit features a PT1/8 port and a built-in magnet for CMSE/DMSE sensors.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X910S FAQ
At 0.5 MPa, the SE32X910S provides 402 N of push force and 345 N of pull force. At 0.7 MPa, the push force is 563 N, with a maximum push capacity of 82 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
No, the adjustable air cushion at both ends only decelerates the piston near the stroke end and does not act as a brake. A standard SE cylinder will drift if air pressure is lost or the valve is centered. For position holding, use the BSE rod lock variant or an external pilot-operated check valve.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X910S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.