Airtac SE80 Standard Cylinder SE80BX700
The AirTAC Airtac SE80 Standard Cylinder SE80BX700 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 700mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke700 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80BX700
The AirTAC SE80BX700 is a double-acting, single-rod ISO 15552 profile cylinder engineered for a 700 mm stroke. It utilizes a corrosion-resistant SUS304 stainless steel rod, making it highly suitable for washdown environments or applications where moisture and chemical exposure would degrade a standard carbon steel shaft. Operating at 0.5 MPa, it generates 2513 N of push force and 2268 N of pull force.
Built with an extruded aluminum barrel that eliminates external tie rods, the body is exceptionally compact and easy to mount flush against machinery. The cylinder features field-adjustable pneumatic cushioning at both ends, allowing technicians to fine-tune the end-of-stroke deceleration via a screw to prevent harsh mechanical impacts when moving heavy loads at high speeds. Note that this specific SKU is not equipped with a position-sensing magnet.
Airtac SE80 Standard Cylinder SE80BX700 Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80BX700 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 700 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80BX700
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×700 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80BX700 Is Used
Bottling Line Diverters
Handles the 2513 N push force required to pivot heavy lane guide rails on high-speed beverage conveyor systems over the 700 mm stroke.
Washdown Food Processing
The SUS304 stainless steel rod survives daily caustic washdowns in meat processing facilities, resisting corrosion where standard rods pit and fail.
Corrugated Box Erectors
Provides the long 700 mm travel and 3518 N thrust at 0.7 MPa needed to pull and form large corrugated cardboard blanks in automated case erectors.
Is the Airtac SE80 Standard Cylinder SE80BX700 the Right Cylinder?
If your application requires less force, stepping down to the 63 mm bore yields a 1559 N push at 0.5 MPa, whereas stepping up to the 100 mm bore provides 3927 N of thrust for heavier payloads. Because this plain SE cylinder lacks a rod lock, it cannot hold a load vertically if air pressure is lost or the valve is centered; you would need to pivot to the BSE series or an external pilot-operated check valve for fail-safe positioning.
At a 700 mm stroke, the 25 mm rod and thread experience significant bending moments under side loads. To prevent premature rod-bearing wear and seal failure, always guide the load externally using linear rails rather than relying on the piston rod to absorb lateral stress. This unit is dimensionally interchangeable per ISO 15552, serving as a drop-in replacement for other ISO 15552 cylinders using the standard PT3/8 port and shared mounting hardware.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80BX700 FAQ
The SE80BX700 delivers 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, and a maximum of 513 kgf at 1.0 MPa. It operates at speeds ranging from 30 to 800 mm/s.
Yes, the SE80BX700 is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. You can drop it into existing mounts designed for other ISO 15552 profile cylinders, matching the 80 mm bore, 700 mm stroke, and PT3/8 porting.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80BX700
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.