Airtac SE80 Standard Cylinder SE80X1650S
The AirTAC Airtac SE80 Standard Cylinder SE80X1650S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 1650mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke1650 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X1650S
The AirTAC SE80X1650S is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding linear motion tasks. It features an 80 mm bore and a 1650 mm stroke, delivering a robust 2513 N push force at 0.5 MPa (3518 N at 0.7 MPa). Because the 1650 mm stroke exceeds the 1500 mm standard maximum, this unit is configured as a non-standard, made-to-order actuator tailored for extended travel distances.
The extruded aluminum barrel design omits external tie rods, yielding a smooth, corrosion-resistant profile that mounts flush in tight machinery spaces. Equipped with a built-in magnet (-S), it directly supports AirTAC CMSE reed and DMSE electronic position sensors for precise end-of-trroke detection. The field-adjustable air cushioning at both ends allows you to tune deceleration on the fly, softening hard impacts at high cycling speeds.
Airtac SE80 Standard Cylinder SE80X1650S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X1650S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 1650 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X1650S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×1650 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X1650S Is Used
Automotive Assembly Line Transfer
Drives long-stroke pallet pushers across 1650 mm spans, utilizing the 2513 N push force to move heavy chassis components between robotic welding stations.
Multi-Tier Storage Retrieval
Extracts deep storage totes in automated retrieval systems, where the 80 mm bore provides the necessary power and the -S magnet tracks fully extended positions.
Large Format Film Unwind
Actuates the primary carriage for heavy pallet wrapping machinery, relying on adjustable end cushions to decelerate the massive 1650 mm travel without slamming.
Is the Airtac SE80 Standard Cylinder SE80X1650S the Right Cylinder?
Selecting this 80 mm bore yields a 2513 N push at 0.5 MPa. If your load is lighter, stepping down to the 63 mm bore reduces the push to 1559 N, saving air volume. For heavier loads, stepping up to the 100 mm bore increases the push to 3927 N. Because this is a standard double-acting cylinder, it will not hold a load if air pressure is lost or the valve is centered; the piston will drift, so a BSE rod lock is required for fail-safe holding.
At 1650 mm of travel, the Ø25 mm piston rod and M20x1.5 thread are subjected to significant bending moments under side loads. An external guide rail is strongly recommended to prevent rod-bearing damage. As a true ISO 15552 cylinder, it is dimensionally interchangeable with other ISO 15552 profile cylinders, allowing you to reuse existing mounting hardware like TC trunnions or FA flanges without redesigning the machine frame.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X1650S FAQ
This 80 mm bore cylinder uses a PT3/8 port and a Ø25 mm rod with an M20x1.5 thread. At 0.5 MPa it provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa the push force is 3518 N, and the maximum rated push force is 513 kgf at 1.0 MPa.
Yes. The SE80X1650S is built to the ISO 15552 / VDMA 24562 dimensional standard, meaning it is a drop-in replacement for other ISO 15552 profile cylinders. You can reuse your existing mounting brackets and sensor setups, though the 1650 mm stroke is a non-standard made-to-order length.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X1650S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.