Airtac SE80 Standard Cylinder SE80X360
The AirTAC Airtac SE80 Standard Cylinder SE80X360 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 360mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke360 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X360
The AirTAC SE80X360 is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver 2513 N of push force at 0.5 MPa and up to 513 kgf at 1.0 MPa. Its extruded aluminum square barrel omits external tie rods, yielding a flush exterior that resists corrosion and simplifies direct mounting on packaging or material handling frames.
This 80 mm bore unit features field-adjustable pneumatic cushioning at both ends to decelerate the 25 mm hard-chrome rod over a 36 mm stroke-end travel, preventing hard impact at high speeds. Because this SKU lacks the -S magnet, it does not support CMSE or DMSE position sensing out of the box.
Airtac SE80 Standard Cylinder SE80X360 Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X360 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 360 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X360
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×360 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X360 Is Used
Carton Erector Drive
Provides the 2513 N push at 0.5 MPa required to reliably pull and erect heavy corrugated carton blanks over the 360 mm stroke in continuous packaging lines.
Pallet Diverting Gate
Actuates heavy lane-diverter gates on roller conveyors, using its 36 mm adjustable end-cushion to soften the 80 mm bore's kinetic impact at high transit speeds.
Press Brake Material Stop
Positions the backgauge stop on a sheet metal press brake, where the tie-rod-free profile allows flush mounting against the machine bed without physical interference.
Is the Airtac SE80 Standard Cylinder SE80X360 the Right Cylinder?
If your load requires less force, stepping down to the 63 mm bore yields 1559 N push at 0.5 MPa, while moving up to the 100 mm bore provides 3927 N push at 0.5 MPa. Keep in mind that a standard SE cylinder will drift and cannot hold a load if air pressure is lost; for position holding, consider the BSE rod lock variant. At 360 mm stroke, the unsupported piston rod is highly susceptible to bending under side loads, so an external guide is strongly recommended to prevent premature rod-bearing wear. This model is dimensionally interchangeable with any ISO 15552 cylinder of the same bore and stroke, utilizing a PT3/8 port and standard mounting accessories.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X360 FAQ
The SE80X360 generates 2513 N of push force and 2268 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 3518 N. The maximum push force is 513 kgf when operated at the 1.0 MPa pressure limit.
Yes, the SE80X360 is dimensionally interchangeable per ISO 15552 standards. You can drop it in as a replacement for any ISO 15552 profile cylinder with an 80 mm bore and 360 mm stroke, using the same PT3/8 port and mounting hardware.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X360
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.