Airtac SE80 Standard Cylinder SE80X450S
The AirTAC Airtac SE80 Standard Cylinder SE80X450S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 450mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke450 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X450S
The AirTAC SE80X450S is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty pneumatics, delivering a robust 2513 N push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush into tight machine envelopes while resisting mechanical degradation.
Equipped with a built-in magnet (-S), this unit seamlessly interfaces with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable pneumatic cushioning at both ends allows technicians to dial in end-stop deceleration via a set screw, softening hard impacts during high-velocity 450 mm strokes.
Airtac SE80 Standard Cylinder SE80X450S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X450S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 450 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X450S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×450 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X450S Is Used
Palletizer Case Pusher
With 2513 N of thrust at 0.5 MPa and a 450 mm stroke, this cylinder easily shoves heavy corrugated cardboard cases onto accumulating pallets in high-speed packaging lines.
Press Brake Ejector
The 80 mm bore generates enough force to strip thick-gauge metal brackets from a press brake die, while the adjustable cushion softens the ejection stroke at full extension.
Heavy Pallet Diverter
Leveraging the 450 mm stroke and 3518 N push at 0.7 MPa, this actuator reliably diverts loaded pallets weighing hundreds of kilograms onto secondary conveyor spurs.
Is the Airtac SE80 Standard Cylinder SE80X450S the Right Cylinder?
Operating at 80 mm bore, this cylinder provides 2513 N of push force at 0.5 MPa. If your application requires less force, stepping down to the 63 mm bore yields 1559 N of push; conversely, scaling up to the 100 mm bore provides 3927 N. Because this is a 450 mm stroke, the unsupported piston rod is highly susceptible to bending under lateral loads—always pair it with an external guide rail to prevent rod-bearing wear. Note that a standard SE cylinder drifts when air is lost; for position holding, explore the BSE rod lock variant. As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct drop-in replacement for other ISO 15552 profile cylinders, utilizing the same PT3/8 port and standardized mounting hardware.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X450S FAQ
The SE80X450S delivers a push force of 2513 N and a pull force of 2268 N at 0.5 MPa. At 0.7 MPa, the push force reaches 3518 N. The maximum push force is 513 kgf at 1.0 MPa, and the operational speed ranges from 30-800 mm/s.
Yes, the SE80X450S is dimensionally interchangeable per ISO 15552 standards. It shares the exact mounting footprint, 25 mm rod, M20x1.5 thread, and PT3/8 port of other ISO 15552 profile cylinders, allowing a direct drop-in retrofit without custom brackets.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X450S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.