Airtac SED Double Rod Cylinder SED32X105
The AirTAC Airtac SED Double Rod Cylinder SED32X105 is a genuine double-acting ISO 15552 double-rod cylinder: a Ø12mm piston rod exits BOTH ends of the Ø32mm bore, giving equal force and speed in both directions and letting you mount tooling or a sensor flag on the back rod. Stroke 105mm, PT1/8 ports, adjustable cushioning.
- BoreØ32 mm
- Stroke105 mm
- Port sizePT1/8
- ConfigurationDouble rod
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SED Double Rod Cylinder SED32X105
The AirTAC SED32X105 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 32mm bore and 105mm stroke. Because a rod exits both end covers, the annulus area is identical on each side, yielding equal force in extend and retract—345 N each way at 0.5 MPa. The extruded aluminum barrel omits external tie rods, maintaining a clean profile while offering field-adjustable air cushioning at both ends.
This SKU lacks the -S magnet option, meaning no CMSE or DMSE position sensing is equipped. The twin 12mm carbon steel rods enhance load guiding against rotation, and the rear rod end can drive a secondary mechanism. With a PT1/8 port and M10x1.25 rod thread, it operates at speeds from 30 to 800 mm/s.
Airtac SED Double Rod Cylinder SED32X105 Technical Specifications
| Model | Airtac SED Double Rod Cylinder SED32X105 |
|---|---|
| Series | SED ISO 15552 double-rod cylinder |
| Bore size | Ø32 mm |
| Stroke | 105 mm |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SED datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Because a rod exits both ends, the effective piston area — and therefore the force — is identical on extend and retract. Actual usable force is lower than theoretical; size with a safety margin.
Model Code: Airtac SED Double Rod Cylinder SED32X105
| SED | ISO 15552 profile-barrel DOUBLE-ROD double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×105 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SED): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SE (single rod), SEJ (double-rod adjustable stroke), BSED (double-rod rod lock).
Where the Airtac SED Double Rod Cylinder SED32X105 Is Used
Web Edge Guiding
Uses the symmetric 345 N force to steer paper or film webs via a rear-rod cam, preventing material drift during high-speed winding.
Dual-Side Pick & Place
Transfers small electronic components between stations, leveraging the twin 12mm rods to resist torsional twist and maintain parallel grip.
Sorting Diverter Arm
Pushes small parcels at 30-800 mm/s, using the rear rod end to mount a limit flag that confirms stroke completion.
Is the Airtac SED Double Rod Cylinder SED32X105 the Right Cylinder?
Choose this 32mm bore when an application demands 345 N of force symmetrically in both directions. If you need less force, there is no smaller SED bore, but stepping up to the 40mm bore provides 528 N at 0.5 MPa. The double-rod design is preferred over a single-rod SE when you need anti-rotation guidance, rear-rod cam actuation, or dual-side tooling. Remember that a plain SED does not hold position on air loss; the piston drifts, and the adjustable cushion only decelerates near stroke end. For fail-safe holding, consider a BSED rod-lock cylinder. When replacing an ISO 15552 unit, match the 32mm bore, 105mm stroke, PT1/8 port, and mounting style (Basic, FA, LB, TC, FTC, TCM1, or TCM2).
Quick checklist
- ✓ Equal force/speed both directions needed?
- ✓ Back-rod space for tooling or a flag
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Support both rod ends; avoid side load.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SED Double Rod Cylinder SED32X105 FAQ
Because the double-rod design has equal piston areas on both sides, it generates 345 N at 0.5 MPa and 483 N at 0.7 MPa in both directions. The maximum force is 70 kgf at 1.0 MPa.
Yes, the SED32X105 is dimensionally interchangeable with other ISO 15552 profile cylinders. Just verify your 105mm stroke, PT1/8 port, and that your mounting falls under the supported set: Basic, FA, LB, TC, FTC, TCM1, or TCM2.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SED Cylinders
Request a Quote for Airtac SED Double Rod Cylinder SED32X105
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.