Airtac SED Double Rod Cylinder SED32X700S
The AirTAC Airtac SED Double Rod Cylinder SED32X700S is a genuine double-acting ISO 15552 double-rod cylinder: a Ø12mm piston rod exits BOTH ends of the Ø32mm bore, giving equal force and speed in both directions and letting you mount tooling or a sensor flag on the back rod. Stroke 700mm, PT1/8 ports, adjustable cushioning.
- BoreØ32 mm
- Stroke700 mm
- Port sizePT1/8
- ConfigurationDouble rod
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SED Double Rod Cylinder SED32X700S
The AirTAC SED32X700S is a double-acting, double-rod profile cylinder built to ISO 15552 dimensional standards. Because a 12mm rod exits both ends, the annulus area is identical on extend and retract, yielding 345N of force each way at 0.5 MPa. This through-rod geometry provides superior anti-rotation stability and allows the rear rod end to drive a secondary mechanism.
Equipped with a standard magnet (-S), this 32mm bore unit triggers CMSE reed or DMSE electronic sensors flush-mounted in the barrel groove. It features field-adjustable air cushioning at both ends (27mm stroke) to decelerate the 700mm travel, and uses a PT1/8 port with an M10x1.25 rod thread.
Airtac SED Double Rod Cylinder SED32X700S Technical Specifications
| Model | Airtac SED Double Rod Cylinder SED32X700S |
|---|---|
| Series | SED ISO 15552 double-rod cylinder |
| Bore size | Ø32 mm |
| Stroke | 700 mm |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SED datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Because a rod exits both ends, the effective piston area — and therefore the force — is identical on extend and retract. Actual usable force is lower than theoretical; size with a safety margin.
Model Code: Airtac SED Double Rod Cylinder SED32X700S
| SED | ISO 15552 profile-barrel DOUBLE-ROD double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×700 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SED): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SE (single rod), SEJ (double-rod adjustable stroke), BSED (double-rod rod lock).
Where the Airtac SED Double Rod Cylinder SED32X700S Is Used
PCB Edge Guiding
Uses the 345N both-way force to center electronic panels. The rear rod simultaneously pushes a limit flag, confirming travel for DMSE sensors.
Lightweight Shuttle Transfer
Moves small plastic components between stations. The twin-rod anti-rotation design prevents the 700mm stroke from twisting under offset loads.
Pick-and-Place Y-Axis
Drives a vertical gripper assembly. Equal force both directions ensures smooth descent and ascent without needing pressure compensation.
Is the Airtac SED Double Rod Cylinder SED32X700S the Right Cylinder?
Choose this 32mm bore when you need precise 345N both-way thrust and twin-rod load balancing. If your application requires less force, there is no smaller bore in this series. If you need more power, stepping up to the 40mm bore provides 528N at 0.5 MPa. For a 700mm stroke, external guide rails are strongly recommended to prevent side-load deflection on the 12mm rod.
A plain SED does not hold position upon air loss; the piston drifts, and the adjustable cushion only decelerates near stroke end. For fail-safe holding, use a BSED double-rod rod lock. To replace an existing ISO 15552 cylinder, match the 32mm bore, 700mm stroke, PT1/8 port, and mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
- ✓ Equal force/speed both directions needed?
- ✓ Back-rod space for tooling or a flag
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Support both rod ends; avoid side load.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SED Double Rod Cylinder SED32X700S FAQ
The SED32X700S generates equal force in both extend and retract directions due to the double-rod design. It outputs 345N at 0.5 MPa, 483N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
A double-rod SED provides identical force both ways and better anti-rotation resistance. The protruding rear rod can also drive a secondary mechanism or sensor cam, which a single-rod cylinder cannot do.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SED Cylinders
Request a Quote for Airtac SED Double Rod Cylinder SED32X700S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.