Airtac TACE Guided Compact Cylinder TACE100X70S
The AirTAC Airtac TACE Guided Compact Cylinder TACE100X70S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø100mm bore and 70mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ100 mm
- Stroke70 mm
- Port size1/4"
- Acting typeDouble acting, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
About the Airtac TACE Guided Compact Cylinder TACE100X70S
A double acting, non-rotating compact cylinder to ISO 21287, the TACE100X70S pairs a 100 mm bore and 70 mm stroke with a hard-anodized aluminium body and an S45C hard-chrome-plated 20 mm rod. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide. At 0.5 MPa it pushes 3927 N and pulls 3769.9 N; at 0.7 MPa those figures climb to 5497.8 N and 5277.9 N, with a theoretical 800.9 kgf at 1.0 MPa.
The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits heavy presses, clamping fixtures and gantries where a full-length cylinder will not go. For sizing, plan on roughly 2356 N of real work at 0.5 MPa (about 0.6 of the push force), which is around 400 kg equivalent - so match loads up to about 200 kg vertical for a 2:1 margin. The -S code on this model means the magnet is fitted, letting CMSE / DMSE switches clamp into the body slots. Air supply is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, with a fixed TPU bumper at each end.
Airtac TACE Guided Compact Cylinder TACE100X70S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE100X70S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø100 mm |
| Stroke | 70 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3770 N |
| 0.7 MPa | 5498 N | 5278 N |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE100X70S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 100 | Bore size in mm. |
| ×70 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE100X70S Is Used
Bearing and bushing press
On an automotive axle line, the twin-guide yoke presses bearings into housings with about 2356 N of usable force at 0.5 MPa while the guide rods keep the press tool square to the bore.
Weldment clamping fixture
Clamping large steel frames before robotic welding: the 100 mm bore holds the joint closed through thermal distortion, and the 70 mm stroke clears robot access in a tight fixture footprint.
Vertical die-component lift
Raising a heavy die insert or stopper block of about 200 kg in a stamping cell, with the 2:1 margin built in; add a pilot check valve because the piston will drift if air pressure drops.
Is the Airtac TACE Guided Compact Cylinder TACE100X70S the Right Cylinder?
This is the top of the ACE bore range: where an 80 mm bore (2513.3 N push at 0.5 MPa) leaves too little margin for a press or clamp load, the 100 mm bore here gives 3927 N push and 3769.9 N pull at the same pressure. The 70 mm stroke sits well inside the 300 mm maximum standard stroke for this bore, so no made-to-order build is needed. Note the piston drifts if air is lost - it never locks or brakes a load - so add a rod lock or pilot check valve where a vertical load must stay put. Mounting options are FB flange, CA/CB clevis, CR and FTC; the female M12x1.75 rod thread and 1/4" PT port suit standard tooling, and the fitted -S magnet accepts CMSE / DMSE switches for end-of-stroke signals.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE100X70S FAQ
At 0.5 MPa the 100 mm bore pushes 3927 N and pulls 3769.9 N. At 0.7 MPa push rises to 5497.8 N (pull 5277.9 N), and the theoretical maximum is 800.9 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a proof pressure of 1.5 MPa (215 psi), running on air filtered to 40 um.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and a fixed TPU bumper at each end absorbs end-of-stroke energy. Because this model carries the -S code, the magnet is fitted, so CMSE / DMSE reed or solid-state switches mount in the body slots for position signals. FB, CA, CB, CR and FTC mountings are available; for outline dimensions, confirm from datasheet.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE100X70S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.