Airtac TACE Guided Compact Cylinder TACE100X75S
The AirTAC Airtac TACE Guided Compact Cylinder TACE100X75S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø100mm bore and 75mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ100 mm
- Stroke75 mm
- Port size1/4"
- Acting typeDouble acting, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
About the Airtac TACE Guided Compact Cylinder TACE100X75S
The largest bore in the ACE family, the TACE100X75S is a double acting, non-rotating compact cylinder: 100 mm bore, 75 mm stroke, 20 mm rod, 1/4" port. At 0.5 MPa it pushes 3927 N and pulls 3769.9 N; at 0.7 MPa those figures rise to 5497.8 N and 5277.9 N, with a theoretical ceiling of 800.9 kgf at 1.0 MPa. In practice, plan on roughly 2356 N of usable push at 0.5 MPa, and for vertical work expect about 400 kg of lift on paper - halve that to a 2:1 margin and you can hang a part of about 200 kg and still be safe.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so this force class fits into press frames and weld fixtures that were never sized for a full-length body. Twin guide rods on a yoke stop the tooling rotating and carry side load, keeping a heavy plate or gripper square without an external guide. The hard-anodized aluminium body carries a hard-chrome plated S45C rod, a fixed TPU bumper absorbs end-of-stroke shock at each end, and because this model carries the -S code the magnet is already fitted, so CMSE / DMSE reed or solid-state switches can be mounted anywhere along the body slots.
Airtac TACE Guided Compact Cylinder TACE100X75S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE100X75S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø100 mm |
| Stroke | 75 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3770 N |
| 0.7 MPa | 5498 N | 5278 N |
| Max (@1.0 MPa) | 801 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE100X75S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 100 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE100X75S Is Used
Bearing press-fit in an automotive assembly cell
A 75 mm stroke is enough to seat a bearing into a hub housing in one controlled move, and the 3927 N push at 0.5 MPa covers typical light press-fit forces without stepping up to a hydraulic unit.
Fixture clamping on a CNC machining line
Twin guide rods keep the clamp plate square against heavy steel fixtures under side load, so the part stays registered through roughing cuts - no external guide rail needed.
Lid clamping on a leak-test station
The fitted -S magnet lets a DMSE switch confirm the clamp is fully closed before the test cycle starts, and the 100 mm bore holds a large cast cover down against test pressure.
Is the Airtac TACE Guided Compact Cylinder TACE100X75S the Right Cylinder?
At 100 mm this is the top of the ACE range - there is no larger bore to step up to. If 3927 N of push at 0.5 MPa is more than the job needs, the 80 mm bore delivers 2513.3 N at the same pressure in the same short body. Note that the piston drifts if air is lost, so for a held or clamped load add a rod lock or a pilot check valve rather than relying on the cylinder itself. Mounting options are FB flange, CA/CB clevis, CR and FTC, and the fitted -S magnet means CMSE / DMSE switches are ready to bolt on for end-of-stroke or mid-stroke signalling.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE100X75S FAQ
At 0.5 MPa the 100 mm bore pushes 3927 N and pulls 3769.9 N. At 0.7 MPa it pushes 5497.8 N and pulls 5277.9 N. The theoretical maximum is 800.9 kgf at 1.0 MPa. For sizing, treat about 2356 N (roughly 0.6 of the 0.5 MPa push) as usable working force, and for vertical lifts assume about 200 kg with a 2:1 safety margin.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a hard-anodized aluminium body, hard-chrome S45C rod and a fixed TPU bumper at both ends. Mounting choices are FB flange, CA/CB clevis, CR and FTC. Because this model carries the -S code, the position magnet is already fitted, so CMSE / DMSE switches can be slid into the body slots for stroke signalling.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE100X75S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.