Airtac TACE Guided Compact Cylinder TACE20X75S
The AirTAC Airtac TACE Guided Compact Cylinder TACE20X75S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø20mm bore and 75mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ20 mm
- Stroke75 mm
- Port sizeM5×0.8
- Acting typeDouble acting, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE20X75S
This double acting, non-rotating compact cylinder pairs a 20 mm bore with a 75 mm stroke and twin guide rods on a yoke, so a gripper or plate stays square without an external guide. At 0.5 MPa it pushes 157.1 N and pulls 117.8 N; at 0.7 MPa those figures rise to 219.9 N and 164.9 N, with a theoretical 32 kgf at 1.0 MPa. The hard-anodized aluminium body with S45C hard-chrome rod and a fixed TPU bumper at both ends runs 30-500 mm/s on 0.15-1.0 MPa (22-145 psi) air filtered to 40 um.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs, guards and gantries. Plan on roughly 94 N of real work at 0.5 MPa (about 0.6 of the push figure), enough to lift about 8 kg vertically with a 2:1 margin. The S code on this model means the magnet is fitted, so CMSE / DMSE reed or solid-state switches can be seated in the body slots; the female M6x1.0 rod thread and M5x0.8 port keep tooling and plumbing simple.
Airtac TACE Guided Compact Cylinder TACE20X75S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE20X75S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø20 mm |
| Stroke | 75 mm |
| Acting type | Double acting, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø20mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 157 N | 118 N |
| 0.7 MPa | 220 N | 165 N |
| Max (@1.0 MPa) | 32 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE20X75S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 20 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE20X75S Is Used
Connector cap ejection
On an electronics assembly line, the 75 mm stroke reaches across a nest to push finished connector caps into a chute, while the twin-guide yoke keeps the ejector pin from twisting under an off-centre part.
Small-part gripper actuation
Clamping plastic housings in a robot cell, the 157.1 N push at 0.5 MPa gives a firm grip on parts up to about 8 kg, and the non-rotating guide rods hold the jaws parallel cycle after cycle.
Vial lane diversion
On a pharmaceutical packaging line, the 75 mm stroke crosses a 60 mm conveyor lane to divert vials into a reject bin, with the TPU bumper softening each stop at 500 mm/s top speed.
Is the Airtac TACE Guided Compact Cylinder TACE20X75S the Right Cylinder?
Between the 16 mm bore (100.5 N push at 0.5 MPa) and the 25 mm bore (245.4 N push at 0.5 MPa), this 20 mm model sits in the middle with 157.1 N push and 117.8 N pull at 0.5 MPa. The 75 mm stroke is inside the 100 mm standard range for this bore, so it is a catalogue item, not a made-to-order length. Note that the piston drifts if air is lost - it is not a lock or brake; add a rod lock or pilot check valve where a load must stay held. FB flange, CA/CB clevis, CR and FTC mountings, PT port thread and the fitted -S magnet for CMSE / DMSE switches complete the package.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE20X75S FAQ
At 0.5 MPa it pushes 157.1 N and pulls 117.8 N; at 0.7 MPa it pushes 219.9 N and pulls 164.9 N. The theoretical maximum is 32 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a proof pressure of 1.5 MPa (215 psi), speed runs 30-500 mm/s, and the rod is 10 mm with a female M6x1.0 thread.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a hard-anodized aluminium barrel, an S45C hard-chrome plated rod and a fixed TPU bumper at each end that decelerates the piston at the ends of travel. Mounting choices are FB flange, CA/CB clevis, CR and FTC. Because this model carries the optional -S magnet, CMSE / DMSE reed or solid-state switches mount directly in the slots around the body.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE20X75S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.