Airtac TACE Guided Compact Cylinder TACE25X100S
The AirTAC Airtac TACE Guided Compact Cylinder TACE25X100S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø25mm bore and 100mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ25 mm
- Stroke100 mm
- Port sizeM5×0.8
- Acting typeDouble acting, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE25X100S
The TACE25X100S is a double acting, non-rotating compact cylinder built to ISO 21287: a 25 mm bore that pushes 245.4 N (about 25 kgf) at 0.5 MPa and 343.6 N at 0.7 MPa over a 100 mm stroke, on a hard-anodized aluminium body with an S45C hard-chrome rod. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or plate stays square without an external guide - a real edge over a plain compact cylinder. The rod ends in a female M6x1.0 thread and the air ports are M5x0.8.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs, guards and gantries where a full-length cylinder will not. A fixed TPU bumper at each end absorbs end-of-stroke shock, and the two-way piston seal stores grease for long service. In practice, plan for about 147 N of real work at 0.5 MPa rather than the full 245.4 N rating, or lift about 12 kg vertically with a 2:1 margin. This model carries the optional -S magnet, so CMSE / DMSE reed or solid-state switches clamp straight onto the body for position signals. Supply 0.15-1.0 MPa (22-145 psi) air filtered to 40 um; speed 30-500 mm/s; proof pressure 1.5 MPa (215 psi).
Airtac TACE Guided Compact Cylinder TACE25X100S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE25X100S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 100 mm |
| Acting type | Double acting, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE25X100S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 25 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE25X100S Is Used
PCB nest clamping
Clamps a circuit-board nest on an SMT placement fixture: 245.4 N at 0.5 MPa holds the board square while the twin-guide yoke keeps the clamp pad from rotating under side load.
Carton flap tuck
Tucks near-side flaps on a small carton sealing head: the 100 mm stroke reaches across the box face and the twin guide rods stop the tuck blade twisting as it enters the flap gap.
Sample tray indexing
Pushes sample trays between stations in a diagnostics analyzer: about 12 kg vertical-lift equivalent with a 2:1 margin, and CMSE / DMSE switches on the -S magnet confirm tray-in-position.
Is the Airtac TACE Guided Compact Cylinder TACE25X100S the Right Cylinder?
At 245.4 N push at 0.5 MPa, this 25 mm bore sits between the 20 mm bore (157.1 N) and the 32 mm bore (402.1 N) in the TACE range. If your tooling needs more than about 147 N of usable force at 0.5 MPa, step up to 32 mm; below roughly 95 N of working load the 20 mm bore saves air and space. The piston drifts when air is lost, so for a held load add a rod lock or pilot check valve. Mount with FB flange, CA/CB clevis, CR or FTC; the fitted -S magnet accepts CMSE / DMSE switches, and the 100 mm stroke covers the full standard range for this bore.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE25X100S FAQ
At 0.5 MPa it pushes 245.4 N and pulls 206.2 N; at 0.7 MPa, 343.6 N push and 288.6 N pull. The theoretical maximum is 50.1 kgf at 1.0 MPa. Keep real working loads near 147 N at 0.5 MPa for a sensible margin, and note the rod drifts if air is lost - use a rod lock or pilot check valve to hold a load.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits shallow guards and tight jig plates. Mount via FB flange, CA/CB clevis, CR or FTC; the rod carries a female M6x1.0 thread and ports are M5x0.8. A fixed TPU bumper at each end absorbs end-of-stroke shock, and because this model carries the -S magnet, CMSE / DMSE reed or solid-state switches mount directly on the body slots.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE25X100S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.