Airtac TACE Guided Compact Cylinder TACE25X10S
The AirTAC Airtac TACE Guided Compact Cylinder TACE25X10S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø25mm bore and 10mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ25 mm
- Stroke10 mm
- Port sizeM5×0.8
- Acting typeDouble acting, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE25X10S
The TACE25X10S is a double acting, non-rotating compact cylinder built to ISO 21287: a 25 mm bore with a 10 mm stroke in a hard-anodized aluminium body fitted with an S45C hard-chrome plated rod. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or plate stays square without an external guide. At 0.5 MPa it pushes 245.4 N and pulls 206.2 N; at 0.7 MPa those figures rise to 343.6 N and 288.6 N, with a theoretical maximum of 50.1 kgf at 1.0 MPa.
The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it drops into tight jigs, guards and gantries where a full-length cylinder will not fit. Plan for roughly 147 N of real work at 0.5 MPa instead of the full rating, and with a 2:1 margin it lifts about 12 kg vertically. The S in the model code means the optional -S magnet is fitted, so CMSE / DMSE reed or solid-state switches can be mounted in the body slots, and a fixed TPU bumper at each end absorbs end-of-stroke energy.
Airtac TACE Guided Compact Cylinder TACE25X10S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE25X10S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 10 mm |
| Acting type | Double acting, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE25X10S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 25 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE25X10S Is Used
Bushing ejection on a small assembly press
A 10 mm stroke is enough to kick a pressed bushing out of its nest, and 245.4 N of push at 0.5 MPa clears light interference fits without hammering the fixture.
Pusher gate for sorting small cartons
On a packaging line diverting 10 kg cartons, the twin-guide yoke keeps the pusher plate square against the side load so packs do not skew as they leave the belt.
Clamp-closed confirmation on a drill jig
Because this -S model carries the magnet, a CMSE or DMSE switch in the body slot signals extend and retract on a 10 mm clamp move, wiring straight into the PLC.
Is the Airtac TACE Guided Compact Cylinder TACE25X10S the Right Cylinder?
For this 10 mm stroke, a 16 mm bore gives only 100.5 N push at 0.5 MPa, while stepping up to a 32 mm bore raises it to 402.1 N - so the 25 mm bore sits in the middle for light clamping and short push moves. Remember the piston drifts when air is lost; for a held load add a rod lock or pilot check valve. Mount with FB flange, CA or CB clevis, CR or FTC, on a PT (blank) or G port thread; the female rod end is M6x1.0. This model already carries the -S magnet code, so position sensing with CMSE / DMSE switches is ready to go.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE25X10S FAQ
At 0.5 MPa the 25 mm bore pushes 245.4 N and pulls 206.2 N; at 0.7 MPa push rises to 343.6 N and pull to 288.6 N. The theoretical maximum is 50.1 kgf at 1.0 MPa. In practice plan on about 147 N of usable push at 0.5 MPa, which lifts about 12 kg vertically with a 2:1 margin. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), and speed 30-500 mm/s on air filtered to 40 um.
It is an ISO 21287 compact cylinder whose hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and a fixed TPU bumper at each end absorbs end-of-stroke energy. Mount with FB flange, CA or CB clevis, CR or FTC on a PT or G port thread (M5x0.8 at this bore); the female rod end is M6x1.0. This -S model carries the optional magnet, so CMSE / DMSE switches can be fitted for position signals. It does not lock or hold a load if air is lost - use a rod lock or pilot check valve where holding matters.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE25X10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.