Airtac TACE Guided Compact Cylinder TACE25X30
The AirTAC Airtac TACE Guided Compact Cylinder TACE25X30 is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø25mm bore and 30mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ25 mm
- Stroke30 mm
- Port sizeM5×0.8
- Acting typeDouble acting, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE25X30
A double acting compact cylinder built to ISO 21287, the TACE25X30 pairs a 25 mm bore with a 30 mm stroke and a 10 mm S45C rod finished in hard chrome. At 0.5 MPa it pushes 245.4 N and pulls 206.2 N, rising to 343.6 N push and 288.6 N pull at 0.7 MPa. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or plate stays square without any external guide - a real edge over a plain compact cylinder.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs, guards and gantries where a full-length body will not fit. For sizing, plan on roughly 147 N of usable force at 0.5 MPa (about 0.6 of the push rating), which lifts about 12 kg vertically with a 2:1 margin. The hard-anodized aluminium body takes M5x0.8 ports and a female M6x1.0 rod thread. This version carries no magnet; order the optional -S code to enable CMSE / DMSE switches.
Airtac TACE Guided Compact Cylinder TACE25X30 Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE25X30 |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 30 mm |
| Acting type | Double acting, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE25X30
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 25 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE25X30 Is Used
Bushings press-fit into aluminium housings
On a small electronics assembly cell, 245.4 N at 0.5 MPa over a 30 mm travel seats light-duty bushings without overloading delicate housings.
Stopper gate on a carton packaging line
The twin-guide yoke holds the stop blade square as cartons strike it at an angle, absorbing side load that would twist a plain compact cylinder.
Jaw alignment on a pick-and-place gripper
Mounted behind parallel jaws, the non-rotating guide rods keep the grip plane true cycle after cycle, so no separate guide rail is needed on the tooling plate.
Is the Airtac TACE Guided Compact Cylinder TACE25X30 the Right Cylinder?
Compare both directions before you commit: the 20 mm bore gives 157.1 N push at 0.5 MPa for lighter clamping, while the 32 mm bore reaches 402.1 N when the load grows. The 30 mm stroke sits well inside the standard range for this bore, so no made-to-order build is needed. Air supply is 0.15-1.0 MPa (22-145 psi) and speed runs 30-500 mm/s. Mounting choices are FB flange, CA/CB clevis, CR and FTC, with PT port threads. Note the piston drifts if air is lost - it never holds or brakes a load, so fit a rod lock or pilot check valve where a position must be kept. No magnet is fitted as standard; add the -S code if you need CMSE / DMSE position sensing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE25X30 FAQ
At 0.5 MPa it pushes 245.4 N and pulls 206.2 N. At 0.7 MPa the figures rise to 343.6 N push and 288.6 N pull. The theoretical maximum is 50.1 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, speed range 30-500 mm/s, and the fluid must be air filtered to 40 um.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and a fixed TPU bumper at each end absorbs end-of-stroke energy. Mounting options include FB flange, CA/CB clevis, CR and FTC, with a female M6x1.0 rod thread and M5x0.8 ports. This model has no magnet; order the optional -S version to run CMSE or DMSE switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE25X30
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.