Airtac TACE Guided Compact Cylinder TACE25X30S
The AirTAC Airtac TACE Guided Compact Cylinder TACE25X30S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø25mm bore and 30mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ25 mm
- Stroke30 mm
- Port sizeM5×0.8
- Acting typeDouble acting, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE25X30S
The TACE25X30S is a double acting, non-rotating compact cylinder built to ISO 21287: a 25 mm bore and 30 mm stroke in a short hard-anodized aluminium body that saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it drops into tight jigs and guarded stations. Twin guide rods on a yoke stop the tooling rotating and carry side load, keeping a gripper or plate square without an external guide. At 0.5 MPa it pushes 245.4 N and pulls 206.2 N.
Because this is the -S variant, the magnet is fitted, so CMSE or DMSE reed and solid-state switches can be clamped anywhere along the body slots to report end positions. For real-world sizing, plan on roughly 147 N of usable work at 0.5 MPa, which is about 12 kg of vertical lift with a 2:1 margin. The S45C hard-chrome plated 10 mm rod runs on a two-way grease-retaining seal, fixed TPU bumpers absorb end-of-stroke shock at both ends, and speed spans 30-500 mm/s at 0.15-1.0 MPa (22-145 psi).
Airtac TACE Guided Compact Cylinder TACE25X30S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE25X30S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 30 mm |
| Acting type | Double acting, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE25X30S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 25 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE25X30S Is Used
Small-part pick and place
On an electronics assembly line, the twin-guide yoke lifts aluminium connector housings weighing up to about 12 kg equivalent vertically, with the fitted magnet confirming grip via a DMSE switch.
Drilling jig clamping
A 30 mm stroke clamps a bracket against a drill jig with 245.4 N at 0.5 MPa, and the non-rotating guide rods hold the clamp shoe square to the hole axis without extra guides.
Mold part ejection
In a compact injection mold, the short body ejects finished caps from a shallow cavity, where the 50%-shorter footprint fits space no full-length cylinder could occupy.
Is the Airtac TACE Guided Compact Cylinder TACE25X30S the Right Cylinder?
Size around the load: the next bore down, TACE20, delivers 157.1 N push at 0.5 MPa, while stepping up to TACE32 gives 402.1 N, so pick the 25 mm bore when your clamp or press force sits between roughly 150 N and 400 N. Remember the piston drifts when air is lost - for a held load add a rod lock or pilot check valve. Mount with FB flange, CA/CB clevis, CR or FTC, and keep the -S magnet order if position sensing with CMSE / DMSE switches is planned.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE25X30S FAQ
At 0.5 MPa it pushes 245.4 N and pulls 206.2 N; at 0.7 MPa push rises to 343.6 N and pull to 288.6 N. The theoretical maximum at 1.0 MPa is 50.1 kgf. Operating range is 0.15-1.0 MPa (22-145 psi) with proof pressure of 1.5 MPa (215 psi), running on air filtered to 40 um at 30-500 mm/s.
The ISO 21287 body is hard-anodized aluminium with threaded covers and a fixed TPU bumper at each end to absorb end-of-stroke energy. Mounting options are FB flange, CA/CB clevis, CR and FTC. As an -S model it carries the optional magnet, so CMSE or DMSE switches mount in the body slots for position feedback; sensors are only usable when that -S magnet is specified.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE25X30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.