Airtac TACE Guided Compact Cylinder TACE25X45S
The AirTAC Airtac TACE Guided Compact Cylinder TACE25X45S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø25mm bore and 45mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ25 mm
- Stroke45 mm
- Port sizeM5×0.8
- Acting typeDouble acting, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE25X45S
Built as a double acting, non-rotating compact cylinder, the AirTAC TACE25X45S uses a 25 mm bore and 45 mm stroke to push 245.4 N and pull 206.2 N at 0.5 MPa, rising to 343.6 N on the extend stroke at 0.7 MPa. The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs, guards and gantry heads where a full-length cylinder will not fit. Twin guide rods on a yoke stop the tooling rotating and carry side load, holding a gripper or plate square with no external guide.
For real work, plan on roughly 147 N of usable push at 0.5 MPa, which lifts about 12 kg vertically with a 2:1 margin - enough for small aluminium parts or a light clamp plate. This S-coded model carries the optional -S magnet, so CMSE / DMSE reed or solid-state switches can be mounted in the body slots for end-of-stroke sensing. A fixed TPU bumper at each end absorbs end-of-stroke energy, the S45C hard-chrome rod runs in a hard-anodized aluminium body, and the female M6x1.0 rod thread with M5x0.8 ports keeps plumbing simple. Speed range is 30-500 mm/s at 0.15-1.0 MPa (22-145 psi).
Airtac TACE Guided Compact Cylinder TACE25X45S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE25X45S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 45 mm |
| Acting type | Double acting, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE25X45S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 25 | Bore size in mm. |
| ×45 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE25X45S Is Used
Pick-and-place of small aluminium housings
Twin guide rods stop the gripper rotating as it lifts housings off a CNC fixture; with about 12 kg of vertical lift at a 2:1 margin, the 45 mm stroke clears the part and returns inside a compact cell.
Staking head on a terminal board
The 245.4 N push at 0.5 MPa (343.6 N at 0.7 MPa) stakes small terminals or rivets on connector boards, and the yoke keeps the punch square to the die without a separate guide bushing.
Diverting flap on a packaging line
Mounted on an FTC foot bracket beside the conveyor, the non-rotating rod swings a sorting flap squarely into the product stream, and the optional -S magnet feeds CMSE switch signals back to the PLC at each end.
Is the Airtac TACE Guided Compact Cylinder TACE25X45S the Right Cylinder?
At 245.4 N push and 206.2 N pull at 0.5 MPa, the 25 mm bore sits between the 20 mm bore (157.1 N push) and the 32 mm bore (402.1 N push); step down if your load is under 150 N, step up once you pass 300 N. The piston drifts if air is lost - it never locks or brakes - so add a rod lock or pilot check valve wherever a load must stay put. FB flange, CA/CB clevis, CR and FTC mountings cover most frames, and because this is the S version the magnet is already in place for CMSE / DMSE switches. Strokes to 150 mm are standard for this bore, so 45 mm is comfortably inside the catalogue range.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE25X45S FAQ
At 0.5 MPa it pushes 245.4 N and pulls 206.2 N; at 0.7 MPa it pushes 343.6 N and pulls 288.6 N. The theoretical maximum is 50.1 kgf at 1.0 MPa. Supply air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), with a 1.5 MPa (215 psi) proof pressure, and the rod travels at 30-500 mm/s.
The ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a fixed TPU bumper at each end absorbing end-of-stroke energy. Mounting options are FB flange, CA/CB clevis, CR and FTC. The S in TACE25X45S means the optional -S magnet is fitted, so CMSE / DMSE reed or solid-state switches mount directly in the body slots; a model ordered without -S carries no magnet.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE25X45S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.