Airtac TACE Guided Compact Cylinder TACE25X50S
The AirTAC Airtac TACE Guided Compact Cylinder TACE25X50S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø25mm bore and 50mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ25 mm
- Stroke50 mm
- Port sizeM5×0.8
- Acting typeDouble acting, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE25X50S
The TACE25X50S is a double acting, non-rotating compact cylinder built to ISO 21287: a 25 mm bore drives a 10 mm rod over a 50 mm stroke, and twin guide rods on a yoke stop the tooling rotating while carrying side load. At 0.5 MPa it pushes 245.4 N and pulls 206.2 N; at 0.7 MPa those figures rise to 343.6 N and 288.6 N, with a theoretical peak of 50.1 kgf at 1.0 MPa. In practice, plan for roughly 147 N of usable push at 0.5 MPa, which lifts about 12 kg vertically with a 2:1 margin.
Its hard-anodized aluminium body with an S45C hard-chrome plated rod saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs, guards and gantries where a full-length body will not fit. The -S code on this model means the magnet is fitted, so CMSE or DMSE reed and solid-state switches can be clamped into the body slots for end-of-stroke sensing. A fixed TPU bumper at each end absorbs end-of-stroke energy, ports are M5x0.8, and the rod end carries a female M6x1.0 thread.
Airtac TACE Guided Compact Cylinder TACE25X50S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE25X50S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 50 mm |
| Acting type | Double acting, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE25X50S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 25 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE25X50S Is Used
Ultrasonic weld clamping
Clamps plastic connector housings in a welding jig with about 147 N of usable push at 0.5 MPa; the twin guide rods keep the clamp pad square to the horn without an external guide.
Small-part diverting
Pushes cartons off a packaging conveyor at a sorting gate - the 245.4 N push at 0.5 MPa over a 50 mm stroke clears the lane quickly at speeds up to 500 mm/s.
Gripper actuation in a pick-and-place cell
Drives compact gripper jaws on an electronics assembly robot; the fitted -S magnet accepts CMSE or DMSE switches so the PLC confirms part presence each cycle.
Is the Airtac TACE Guided Compact Cylinder TACE25X50S the Right Cylinder?
For light clamping up to about 157 N at 0.5 MPa, the 20 mm bore is enough; step up to the 32 mm bore (402.1 N push at 0.5 MPa) when the fixture needs more muscle. This cylinder drifts when air is lost - it is not a lock or brake, so add a rod lock or pilot check valve wherever a load must stay held. Mounting choices are FB flange, CA/CB clevis, CR and FTC, and because the -S magnet is fitted on this model, CMSE / DMSE switches can report rod position straight away.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE25X50S FAQ
At 0.5 MPa it pushes 245.4 N and pulls 206.2 N. At 0.7 MPa the push rises to 343.6 N with a pull of 288.6 N. The theoretical maximum is 50.1 kgf at 1.0 MPa. Keep real working loads near 147 N at 0.5 MPa so the cylinder is not run at its limit.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and FB flange, CA/CB clevis, CR and FTC mountings are available. A fixed TPU bumper at each end absorbs end-of-stroke energy. Because this model carries the -S code, the magnet is fitted and CMSE / DMSE reed or solid-state switches can be mounted in the body slots.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE25X50S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.