Airtac TACE Guided Compact Cylinder TACE25X55S
The AirTAC Airtac TACE Guided Compact Cylinder TACE25X55S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø25mm bore and 55mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ25 mm
- Stroke55 mm
- Port sizeM5×0.8
- Acting typeDouble acting, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE25X55S
The AirTAC TACE25X55S is a double acting, non-rotating compact cylinder built to ISO 21287: a 25 mm bore drives a 10 mm rod over a 55 mm stroke, with twin guide rods on a yoke that stop the tooling rotating and carry side load. At 0.5 MPa it pushes 245.4 N and pulls 206.2 N; at 0.7 MPa those figures rise to 343.6 N and 288.6 N, with a theoretical peak of 50.1 kgf at 1.0 MPa. In practice, plan on roughly 147 N of usable push at 0.5 MPa - about a 12 kg vertical lift with a 2:1 margin.
The hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so this unit drops into tight jigs and gantry plates where a full-length body will not fit. The S45C hard-chrome rod runs in a two-way grease-retaining seal, and a fixed TPU bumper absorbs end-of-stroke energy at both ends. Because this model carries the -S magnet code, CMSE or DMSE reed and solid-state switches can be clamped straight into the body slots; the M5x0.8 port takes PT threading and speed spans 30-500 mm/s.
Airtac TACE Guided Compact Cylinder TACE25X55S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE25X55S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 55 mm |
| Acting type | Double acting, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE25X55S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 25 | Bore size in mm. |
| ×55 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE25X55S Is Used
Gripper actuation on a compact assembly cell
Twin guide rods keep a two-finger gripper square while it closes on connector housings; 245.4 N of push at 0.5 MPa clamps the small part without any external guide.
Flap press under low machine guarding
The 55 mm stroke and short ISO 21287 body tuck beneath a guard rail on a cartoning line, pressing carton flaps with about 147 N of working force at 0.5 MPa.
PCB test fixture clamping
The female M6x1.0 rod thread bolts on a pressure plate that holds boards flat during pin testing, while CMSE switches report end positions through the -S magnet.
Is the Airtac TACE Guided Compact Cylinder TACE25X55S the Right Cylinder?
If 245.4 N of push at 0.5 MPa is more than your station needs, the bore 16 TACE delivers 100.5 N; when the load grows past about 147 N of working force, step up to the bore 32, which pushes 402.1 N. Remember the rod drifts the moment air is lost - for a held position add a rod lock or pilot check valve. FB flange, CA/CB clevis, CR and FTC mountings bolt on without extra hardware, and the fitted -S magnet lets CMSE / DMSE switches sit anywhere along the body slots.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE25X55S FAQ
At 0.5 MPa the 25 mm bore pushes 245.4 N and pulls 206.2 N; at 0.7 MPa it pushes 343.6 N and pulls 288.6 N. The theoretical maximum is 50.1 kgf at 1.0 MPa. Operating pressure spans 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof rating, and speed runs 30-500 mm/s.
The hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and FB, CA, CB, CR or FTC mountings bolt straight on. This model carries the optional -S magnet, so CMSE or DMSE reed or solid-state switches clamp into the body slots for end-of-stroke signalling. A fixed TPU bumper at each end absorbs stop energy; the rod will drift if air is lost, so use a rod lock or pilot check valve to hold a load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE25X55S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.