Airtac TACE Guided Compact Cylinder TACE25X80S
The AirTAC Airtac TACE Guided Compact Cylinder TACE25X80S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø25mm bore and 80mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ25 mm
- Stroke80 mm
- Port sizeM5×0.8
- Acting typeDouble acting, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE25X80S
Double acting and non-rotating, the AirTAC TACE25X80S is an ISO 21287 compact cylinder with a 25 mm bore and 80 mm stroke: 245.4 N push and 206.2 N pull at 0.5 MPa. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or plate stays square without an external guide. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it drops into tight jigs, guards and gantries where a full-length cylinder will not fit.
At 0.5 MPa, plan for roughly 147 N of usable push (about 0.6 of the 245.4 N rating), which lifts about 12 kg vertically with a 2:1 margin. The hard-anodized aluminium body runs an S45C hard-chrome plated rod, a fixed TPU bumper at each end absorbs stroke-end shock, and the fitted -S magnet accepts CMSE / DMSE switches for end-position sensing. Supply air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, M5x0.8 port, female rod thread M6x1.0.
Airtac TACE Guided Compact Cylinder TACE25X80S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE25X80S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 80 mm |
| Acting type | Double acting, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE25X80S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 25 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE25X80S Is Used
Pick-and-place of connector housings
On an electronics assembly cell, the twin-guide yoke keeps a vacuum cup plate square over a PCB tray while the 80 mm stroke crosses a fixture rail; 245.4 N push at 0.5 MPa handles the downstroke with margin.
Carton flap tucking on a packaging line
Mounted under a carton sealer, the cylinder retracts a flap tucker with 206.2 N pull at 0.5 MPa, and the 80 mm stroke clears the product stream between cartons at up to 500 mm/s.
Squaring vials before a filling station
A non-rotating squaring plate pushed by the 25 mm bore lines up small vials on a lab filler conveyor; the guide rods stop the plate twisting, and the fitted -S magnet with a DMSE switch confirms the plate is home.
Is the Airtac TACE Guided Compact Cylinder TACE25X80S the Right Cylinder?
Sizing both ways: the bore 20 TACE20X80S gives 157.1 N push at 0.5 MPa, while bore 32 reaches 402.1 N at the same pressure. This 25 mm bore sits between them with 245.4 N push and 206.2 N pull, enough for a 12 kg vertical lift at a 2:1 margin. The 80 mm stroke is inside the standard range for this bore, so no made-to-order length is required. Note that the piston drifts when air is lost - it never holds or brakes a load - so add a rod lock or pilot check valve where a position must be kept. FB flange, CA/CB clevis, CR and FTC mountings suit the yoke, and because the -S magnet is fitted on this model, CMSE / DMSE switches can be added straight into the body slots.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE25X80S FAQ
At 0.5 MPa it pushes 245.4 N and pulls 206.2 N; at 0.7 MPa it pushes 343.6 N and pulls 288.6 N. The theoretical maximum is 50.1 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a proof pressure of 1.5 MPa (215 psi). For real work, count on about 147 N of push at 0.5 MPa, roughly a 12 kg vertical lift with a 2:1 margin.
It is an ISO 21287 short-body cylinder: hard-anodized aluminium body with a roller-burnished bore, S45C hard-chrome rod, threaded aluminium covers and a fixed TPU bumper at each end. The body saves about 50% of the mounting length of an ISO 15552 profile cylinder. Mounting options are FB flange, CA/CB clevis, CR and FTC. The -S magnet is fitted on this model, so CMSE / DMSE reed or solid-state switches mount directly in the body slots; the female rod thread is M6x1.0 and the port is M5x0.8.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE25X80S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.