Airtac TACE Guided Compact Cylinder TACE25X90S
The AirTAC Airtac TACE Guided Compact Cylinder TACE25X90S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø25mm bore and 90mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ25 mm
- Stroke90 mm
- Port sizeM5×0.8
- Acting typeDouble acting, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE25X90S
The TACE25X90S is a double acting, non-rotating ISO 21287 compact cylinder: a 25 mm bore with a 90 mm stroke that pushes 245.4 N and pulls 206.2 N at 0.5 MPa, rising to 343.6 N at 0.7 MPa. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or plate stays square without an external guide - a real edge over a plain compact cylinder.
Its hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs, guards and gantries. Plan on roughly 147 N of real work at 0.5 MPa (about 0.6 of the push figure); with a 2:1 margin that lifts about 12.5 kg vertically, enough to match a real part weight. The -S code on this model means the magnet is fitted, so CMSE / DMSE reed or solid-state switches mount straight into the body slots. A fixed TPU bumper absorbs end-of-stroke energy at both ends, and the cylinder runs on 0.15-1.0 MPa (22-145 psi) at 30-500 mm/s.
Airtac TACE Guided Compact Cylinder TACE25X90S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE25X90S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 90 mm |
| Acting type | Double acting, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE25X90S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 25 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE25X90S Is Used
CNC fixture clamping
Clamps a machined aluminium bracket in a milling fixture. The twin-guide yoke keeps the clamp pad square under side load, and the usable force of about 147 N at 0.5 MPa holds the part through light cuts.
Small-parts ejection on packaging lines
Pushes blister packs off a conveyor lane at end of cycle. The 90 mm stroke clears the full lane width, and the fitted magnet lets a CMSE switch confirm every extend stroke.
Gripper actuation on a pick-and-place gantry
Drives a parallel gripper loading plastic connectors into trays. The non-rotating twin guide rods keep the jaws aligned without an external guide, and the short body fits the tight gantry cross-slide.
Is the Airtac TACE Guided Compact Cylinder TACE25X90S the Right Cylinder?
This 25 mm bore pushes 245.4 N at 0.5 MPa. If your load is lighter, the 20 mm bore delivers 157.1 N at the same pressure; if you need more, step up to the 32 mm bore at 402.1 N. The piston drifts when air is lost, so for a load that must stay put add a rod lock or pilot check valve. Mounting choices are FB flange, CA/CB clevis, CR and FTC, with no rod-thread code on the yoke; the rod end carries a female M6x1.0 thread. The 90 mm stroke sits inside the 150 mm standard range for bore 25, and the magnet is already fitted on this -S model, so CMSE / DMSE switching works out of the box.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE25X90S FAQ
At 0.5 MPa it pushes 245.4 N and pulls 206.2 N; at 0.7 MPa it pushes 343.6 N and pulls 288.6 N; the theoretical maximum is 50.1 kgf at 1.0 MPa. The bore is 25 mm with a 10 mm hard-chrome S45C rod, the air port is M5x0.8 (PT thread), and the rod end carries a female M6x1.0 thread. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, speed 30-500 mm/s, and temperature -20 to +70 C.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it fits cramped jigs and gantries. A fixed TPU bumper at each end absorbs end-of-stroke energy. Mounting options are FB flange, CA/CB clevis, CR and FTC. The optional -S magnet is fitted on this model, so CMSE / DMSE switches mount in the body slots for end-position sensing. Note the piston does not hold position when air is lost - use a rod lock or pilot check valve for a held load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE25X90S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.