Airtac TACE Guided Compact Cylinder TACE32X70
The AirTAC Airtac TACE Guided Compact Cylinder TACE32X70 is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø32mm bore and 70mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ32 mm
- Stroke70 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE32X70
The TACE32X70 is a double acting, non-rotating compact cylinder built to ISO 21287: a 32 mm bore with a 70 mm stroke in a hard-anodized aluminium body whose roller-burnished bore and S45C hard-chrome rod stand up to continuous cycling. Its short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it drops into tight jigs, guards and gantries where a full-length body will not fit. Twin guide rods on a yoke stop the tooling rotating and carry side load, keeping a gripper or plate square without an external guide.
At 0.5 MPa this bore pushes 402.1 N and pulls 345.6 N; at 0.7 MPa that rises to 563 N push and 483.8 N pull, with a theoretical 82 kgf at 1.0 MPa. Plan on roughly 241 N of real work at 0.5 MPa, and with a 2:1 margin the rod lifts about 20 kg vertically, so you can match a fixture or part weight straight off the datasheet. The rod ends in a female M8x1.25 thread, air ports are 1/8" PT, speed runs 30-500 mm/s between 0.15-1.0 MPa (22-145 psi), and a fixed TPU bumper at each end absorbs end-of-stroke shock. The magnet is the optional -S code; without it no CMSE or DMSE switch can be mounted.
Airtac TACE Guided Compact Cylinder TACE32X70 Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE32X70 |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 70 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE32X70
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 32 | Bore size in mm. |
| ×70 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE32X70 Is Used
Pick-and-place on a PCB test gantry
The 70 mm stroke carries a vacuum plate down to the test nest while the twin-guide yoke keeps the plate square over the connectors, delivering 402.1 N of push at 0.5 MPa for consistent contact.
Clamp fixture for aluminium extrusion machining
Side thrust from an offset clamp arm is taken by the guide rods, not the rod seal; plan on about 241 N of usable clamp force at 0.5 MPa on this 32 mm bore.
Lifting small castings into a wash station
With a 2:1 margin the rod lifts about 20 kg vertically, so a light casting carrier can be raised the full 70 mm and returned by air alone at 30-500 mm/s.
Is the Airtac TACE Guided Compact Cylinder TACE32X70 the Right Cylinder?
Size by force: the 25 mm bore gives 245.4 N push at 0.5 MPa, while the 40 mm bore reaches 628.3 N - if your clamp or lift needs more than the TACE32X70's 402.1 N, step up. Remember the piston drifts when air is lost, so for a held load add a rod lock or pilot check valve. Mount with FB flange, CA/CB clevis, CR or FTC; order the -S code if you want the optional magnet for CMSE / DMSE switches, since the base unit carries no magnet.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE32X70 FAQ
At 0.5 MPa it pushes 402.1 N and pulls 345.6 N; at 0.7 MPa it pushes 563 N and pulls 483.8 N; the theoretical maximum is 82 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, and the 32 mm bore breathes through 1/8" PT ports.
It is an ISO 21287 compact cylinder - about 50% shorter in mounting length than an ISO 15552 profile cylinder - with a fixed TPU bumper at both ends to absorb end-of-stroke shock. Mount it with an FB flange, CA/CB clevis, CR or FTC foot. Position switches (CMSE / DMSE) work only when you order the optional -S magnet; the standard TACE32X70 has no magnet fitted.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE32X70
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.