Airtac TACE Guided Compact Cylinder TACE50X35S
The AirTAC Airtac TACE Guided Compact Cylinder TACE50X35S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø50mm bore and 35mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ50 mm
- Stroke35 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE50X35S
The TACE50X35S is a double acting, non-rotating compact cylinder built to ISO 21287: a 50 mm bore and 35 mm stroke in a hard-anodized aluminium body with an S45C hard-chrome plated 16 mm rod. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or plate stays square without an external guide. At 0.5 MPa it pushes 981.7 N and pulls 881.2 N; at 0.7 MPa those figures rise to 1374.4 N and 1233.7 N, with a theoretical maximum of 200.2 kgf at 1.0 MPa.
The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs and guarding where a full-length cylinder will not fit. For sizing, plan on roughly 589 N of real work at 0.5 MPa, which lifts about 50 kg vertically with a 2:1 margin. This model carries the optional -S magnet, so CMSE or DMSE reed and solid-state switches clamp straight into the body slots for end-of-stroke sensing. Operating range is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, with a fixed TPU bumper at both ends.
Airtac TACE Guided Compact Cylinder TACE50X35S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE50X35S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø50 mm |
| Stroke | 35 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 881 N |
| 0.7 MPa | 1374 N | 1234 N |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE50X35S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 50 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE50X35S Is Used
Fixture clamping on a CNC pallet
Clamping aluminium die-cast housings in a machining fixture: the 35 mm stroke clears part load-and-unload, and the roughly 589 N of usable push at 0.5 MPa holds the workpiece square through the cut.
Case squaring on a carton line
Pushing cartons flush against a backstop before taping: the twin-guide yoke keeps the pusher plate from rotating under off-center loads, so cases leave the station at a clean right angle.
Pick-and-place lift at an assembly cell
Raising a machined bracket into an upper nest: with a 2:1 margin the 50 mm bore lifts about 50 kg vertically, and the -S magnet feeds a CMSE switch signal to the PLC at both stroke ends.
Is the Airtac TACE Guided Compact Cylinder TACE50X35S the Right Cylinder?
At 981.7 N push at 0.5 MPa, the 50 mm bore sits between the 40 mm size (628.3 N) and the 63 mm size (1558.6 N): step down if your load needs under about 600 N, step up if you want more than the roughly 589 N of usable force this bore gives. The piston drifts when air is lost and never locks a load, so add a rod lock or pilot check valve where a position must be held. Mounting choices are FB flange, CA/CB clevis, CR and FTC; the -S magnet on this model lets CMSE / DMSE switches read stroke position directly.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE50X35S FAQ
At 0.5 MPa the cylinder pushes 981.7 N and pulls 881.2 N; at 0.7 MPa it reaches 1374.4 N push and 1233.7 N pull, with a theoretical maximum of 200.2 kgf at 1.0 MPa. For real sizing, count on about 589 N of usable push at 0.5 MPa, roughly a 50 kg vertical lift with a 2:1 margin. It runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi) and travels at 30-500 mm/s.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and the fixed TPU bumper absorbs end-of-stroke energy at both ends with no adjustment needed. Mounting options include FB flange, CA/CB clevis, CR and FTC. Because this model carries the optional -S magnet, CMSE or DMSE reed and solid-state switches mount in the body slots; without the -S code there is no magnet. The rod end is female M10x1.5 and the port is 1/8" PT.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE50X35S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.