Airtac TACE Guided Compact Cylinder TACE50X45S
The AirTAC Airtac TACE Guided Compact Cylinder TACE50X45S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø50mm bore and 45mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ50 mm
- Stroke45 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE50X45S
The TACE50X45S is a double acting, non-rotating compact cylinder built to ISO 21287: a 50 mm bore with a 45 mm stroke in a hard-anodized aluminium body whose short profile saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide. At 0.5 MPa it pushes 981.7 N and pulls 881.2 N; at 0.7 MPa those figures rise to 1374.4 N and 1233.7 N, with a theoretical maximum of 200.2 kgf at 1.0 MPa.
For real work, plan on roughly 590 N (about 60% of the push figure) at 0.5 MPa, which lifts about 50 kg vertically with a 2:1 margin. A fixed TPU bumper at each end absorbs end-of-stroke shock, the 16 mm rod carries a female M10x1.5 thread, and the 1/8" port is set by the bore. The fitted -S magnet accepts CMSE / DMSE reed or solid-state switches for end-of-stroke sensing. Operating window is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, temperature -20 to +70 C.
Airtac TACE Guided Compact Cylinder TACE50X45S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE50X45S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø50 mm |
| Stroke | 45 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 881 N |
| 0.7 MPa | 1374 N | 1234 N |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE50X45S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 50 | Bore size in mm. |
| ×45 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE50X45S Is Used
Bearing press station
Short-strike pressing of bushings into aluminium control-arm brackets on an automotive subassembly line, where the twin-guide yoke keeps the punch square over the 45 mm stroke.
Carton flap tuck-down
Tucking flaps on a carton sealing head at up to 500 mm/s, with the 981.7 N push handling stiff board and a CMSE switch confirming each cycle through the fitted magnet.
Fixture clamp in a tight guard
Locating clamp on a machine-tool fixture inside a cramped guard, using the compact body that saves about 50% of the mounting length of an ISO 15552 profile cylinder.
Is the Airtac TACE Guided Compact Cylinder TACE50X45S the Right Cylinder?
At 981.7 N push at 0.5 MPa, the 50 mm bore sits between the 32 mm (402.1 N) and 63 mm (1558.6 N) sizes: step down for light clamping, step up for heavier press or lift work. Remember the piston drifts if air is lost - it is not a lock - so add a rod lock or pilot check valve where a load must stay held. Mounting choices are FB flange, CA/CB clevis, CR and FTC; this model already carries the -S magnet, so CMSE / DMSE switches can be fitted straight away.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE50X45S FAQ
At 0.5 MPa it pushes 981.7 N and pulls 881.2 N; at 0.7 MPa it pushes 1374.4 N and pulls 1233.7 N; the theoretical maximum is 200.2 kgf at 1.0 MPa. Running pressure is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, and speed spans 30-500 mm/s.
It is an ISO 21287 compact cylinder with a hard-anodized aluminium body, an S45C hard-chrome rod and a fixed TPU bumper at both ends; its mounting length runs about 50% shorter than an ISO 15552 profile cylinder. This model carries the optional -S magnet, so CMSE / DMSE reed or solid-state switches can be mounted; FB, CA, CB, CR and FTC mountings are available and the rod end is female M10x1.5.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE50X45S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.