Airtac TACE Guided Compact Cylinder TACE50X50S
The AirTAC Airtac TACE Guided Compact Cylinder TACE50X50S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø50mm bore and 50mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ50 mm
- Stroke50 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE50X50S
The TACE50X50S is a double acting, non-rotating compact cylinder built to ISO 21287: a 50 mm bore drives a 16 mm hard-chrome-plated S45C rod over a 50 mm stroke, while twin guide rods on a yoke stop the tooling rotating and carry side load. At 0.5 MPa it pushes 981.7 N and pulls 881.2 N; at 0.7 MPa those rise to 1374.4 N push and 1233.7 N pull, with a theoretical peak of 200.2 kgf at 1.0 MPa.
Its hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs, guards and gantries where a full-length body will not fit. For sizing, plan on roughly 589 N of usable push at 0.5 MPa - about 50 kg of vertical lift once you halve the 100 kg theoretical figure for a 2:1 margin. This model carries the optional -S magnet, so CMSE / DMSE reed or solid-state switches can be mounted for position feedback. Air supply is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, with a fixed TPU bumper at each end.
Airtac TACE Guided Compact Cylinder TACE50X50S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE50X50S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø50 mm |
| Stroke | 50 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 881 N |
| 0.7 MPa | 1374 N | 1234 N |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE50X50S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 50 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE50X50S Is Used
Clamping die-cast housings on a machining fixture
The 981.7 N push at 0.5 MPa holds an aluminium gearbox housing square while it is drilled, and the twin-guide yoke keeps the clamp plate from twisting under side load.
Lift-and-press station under a low gantry
A 50 mm stroke presses connector covers onto electronics enclosures; the short ISO 21287 body fits where an ISO 15552 profile cylinder cannot, and the -S magnet with a DMSE switch confirms rod position.
Ejecting filled cartons on a packaging conveyor
With about 50 kg of vertical lift available at a 2:1 margin, the cylinder pushes sealed cartons off the line; a pilot check valve is recommended if supply pressure could drop mid-stroke.
Is the Airtac TACE Guided Compact Cylinder TACE50X50S the Right Cylinder?
At 981.7 N push at 0.5 MPa, the 50 mm bore sits between the 40 mm (628.3 N push) and the 63 mm (1558.6 N push), so step down if your clamp force is under about 600 N or step up above roughly 900 N. Remember the piston drifts when air is lost - it never holds or brakes a load - so add a rod lock or pilot check valve if the load must stay put. Mounting covers FB flange, CA/CB clevis, CR and FTC; the fitted -S magnet means CMSE / DMSE switches work out of the box, and the 1/8" PT ports suit standard 6 mm or 8 mm tubing fittings.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE50X50S FAQ
At 0.5 MPa it pushes 981.7 N and pulls 881.2 N; at 0.7 MPa push is 1374.4 N and pull is 1233.7 N. The theoretical maximum is 200.2 kgf at 1.0 MPa. Operating pressure spans 0.15-1.0 MPa (22-145 psi), proof pressure is 1.5 MPa (215 psi), and speed runs 30-500 mm/s on air filtered to 40 um.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and a fixed TPU bumper at each end absorbs end-of-stroke shock. Mounting options are FB flange, CA/CB clevis, CR and FTC. This model carries the -S magnet, so CMSE / DMSE reed or solid-state switches can be fitted; ports are 1/8" PT and the rod end has a female M10x1.5 thread.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE50X50S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.