Airtac TACE Guided Compact Cylinder TACE50X75S
The AirTAC Airtac TACE Guided Compact Cylinder TACE50X75S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø50mm bore and 75mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ50 mm
- Stroke75 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE50X75S
Double acting and non-rotating, the AirTAC TACE50X75S pairs a 50 mm bore with a 75 mm stroke in an ISO 21287 compact body. At 0.5 MPa (22-145 psi operating band) it pushes 981.7 N and pulls 881.2 N, rising to 1374.4 N push at 0.7 MPa. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide - a real edge over a plain compact cylinder. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it drops into tight jigs, guards and gantries.
Build quality is genuine AirTAC: a hard-anodized aluminium-alloy body with a roller-burnished bore, an S45C carbon-steel piston rod with hard-chrome plating, and covers threaded onto the body for easy service. A fixed TPU bumper at each end absorbs end-of-stroke energy. This model carries the optional -S magnet, so CMSE / DMSE reed or solid-state switches can be mounted for end-of-stroke signal. As a rule of thumb, plan for about 589 N (roughly 0.6 of the push force) of real work at 0.5 MPa, and expect it to lift about 50 kg vertically with a 2:1 margin (the theoretical figure is about 100 kg).
Airtac TACE Guided Compact Cylinder TACE50X75S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE50X75S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø50 mm |
| Stroke | 75 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 881 N |
| 0.7 MPa | 1374 N | 1234 N |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE50X75S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 50 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE50X75S Is Used
Press-fit staking station
A 75 mm stroke and 981.7 N push at 0.5 MPa suit staking pins or pressing bearings into housings on an electronics assembly line, with the twin-guide yoke keeping the punch square to the part.
CNC pallet clamping
Clamps fixture pallets on a machining centre: the non-rotating twin guide rods hold the clamp shoe aligned under side load, and the compact body fits inside the fixture base where a longer cylinder will not.
Carton ejection pusher
Pushes cartons off a conveyor lane at 30-500 mm/s; the -S magnet feeds CMSE / DMSE switch signals to the PLC for extend and retract confirmation, and the TPU bumper quiets each end of stroke.
Is the Airtac TACE Guided Compact Cylinder TACE50X75S the Right Cylinder?
Size by force: the 32 mm bore gives 402.1 N push at 0.5 MPa, so step up to this 50 mm bore (981.7 N) when clamping or pressing loads exceed roughly 400 N; step to the 63 mm bore (1558.6 N) if you need more headroom at the same pressure. The 75 mm stroke sits well inside the 250 mm standard range for this bore, so no made-to-order stroke is needed. Remember the piston drifts if air is lost - it does not lock or hold a load - so add a rod lock or pilot check valve where a held position matters. Mounting choices are FB flange, CA/CB clevis, CR and FTC, and the -S magnet on this unit lets you fit CMSE / DMSE switches straight away.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE50X75S FAQ
At 0.5 MPa it pushes 981.7 N and pulls 881.2 N; at 0.7 MPa it pushes 1374.4 N and pulls 1233.7 N. The theoretical maximum is 200.2 kgf at 1.0 MPa. For sizing, plan on about 589 N of usable push at 0.5 MPa, which corresponds to lifting about 50 kg vertically with a 2:1 margin.
It is an ISO 21287 compact cylinder with a hard-anodized aluminium body, S45C hard-chrome rod, 1/8" PT ports and a fixed TPU bumper at both ends; the short body saves about 50% of the mounting length of an ISO 15552 profile cylinder. This model carries the optional -S magnet, so CMSE / DMSE reed or solid-state switches can be mounted. Mounting options are FB flange, CA/CB clevis, CR and FTC, and the rod end has an M10x1.5 female thread.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE50X75S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.