Airtac TACE Guided Compact Cylinder TACE50X90
The AirTAC Airtac TACE Guided Compact Cylinder TACE50X90 is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø50mm bore and 90mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ50 mm
- Stroke90 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE50X90
The TACE50X90 is a double acting, non-rotating compact cylinder built to ISO 21287: a 50 mm bore driving a 16 mm hard-chrome-plated S45C rod over a 90 mm stroke, with twin guide rods on a yoke that stop the tooling rotating and carry side load. At 0.5 MPa it pushes 981.7 N and pulls 881.2 N; at 0.7 MPa those figures rise to 1374.4 N and 1233.7 N, with a theoretical maximum of 200.2 kgf at 1.0 MPa.
The hard-anodized aluminium body keeps the mounting length about 50% shorter than an ISO 15552 profile cylinder, so this 90 mm stroke unit fits tight jigs, guards and gantries. A fixed TPU bumper at each end absorbs end-of-stroke shock, and in practice the rod lifts about 50 kg vertically at 0.5 MPa with a 2:1 margin (plan on roughly 589 N of real work). Position sensing needs the optional -S magnet, which enables CMSE / DMSE switches; without -S no magnet is fitted.
Airtac TACE Guided Compact Cylinder TACE50X90 Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE50X90 |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø50 mm |
| Stroke | 90 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 881 N |
| 0.7 MPa | 1374 N | 1234 N |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE50X90
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 50 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE50X90 Is Used
Bearing press-fit station
The 981.7 N push at 0.5 MPa seats ball bearings into aluminium pump housings on a small assembly cell, while the twin-guide yoke keeps the arbor square to the bore without an external guide.
Carton flap tuck-down
Mounted above a packaging conveyor, the 90 mm stroke presses folding carton flaps flat before sealing, and the short ISO 21287 body fits under a low guard where a full-length profile cylinder will not.
CNC fixture clamping
Two TACE50X90 units clamp aluminium brackets against hardened stops in a machining fixture; the non-rotating rods hold the clamp plates parallel, and the fixed TPU bumpers quiet each clamp cycle.
Is the Airtac TACE Guided Compact Cylinder TACE50X90 the Right Cylinder?
Size by force: if 981.7 N push at 0.5 MPa is more than the job needs, the bore 32 TACE gives 402.1 N; if the load grows, step up to bore 63 for 1558.6 N at the same pressure. Remember the piston drifts when air is lost - it never holds or brakes a load - so add a rod lock or pilot check valve where a position must be kept.
The 1/8" port and M10x1.5 female rod thread suit standard fittings, and FB flange, CA/CB clevis, CR or FTC mountings cover most frames. Order the -S code only if CMSE / DMSE switch sensing is required.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE50X90 FAQ
At 0.5 MPa the 50 mm bore pushes 981.7 N and pulls 881.2 N. At 0.7 MPa push rises to 1374.4 N and pull to 1233.7 N. The theoretical maximum is 200.2 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, speed range 30-500 mm/s, and air filtered to 40 um. For sizing, treat about 589 N as the usable push at 0.5 MPa, which lifts roughly 50 kg vertically with a 2:1 margin.
It is an ISO 21287 compact cylinder whose hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with threaded aluminium covers for easy service and a fixed TPU bumper at both stroke ends. Mounting choices are FB flange, CA/CB clevis, CR and FTC; the rod end is a female M10x1.5 thread and the port is 1/8". Sensing via CMSE / DMSE switches requires the optional -S magnet - without that code no magnet is installed.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE50X90
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.