Airtac TACE Guided Compact Cylinder TACE63X100S
The AirTAC Airtac TACE Guided Compact Cylinder TACE63X100S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 100mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke100 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE63X100S
A double acting, non-rotating actuator built to ISO 21287, the TACE63X100S pairs a 63 mm bore with a 100 mm stroke, and twin guide rods on a yoke stop the tooling rotating while carrying side load. At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N; at 0.7 MPa those figures climb to 2182.1 N and 2041.3 N, with a theoretical peak of 317.9 kgf at 1.0 MPa. The hard-anodized aluminium body carries a 16 mm S45C hard-chrome rod with an M10x1.5 female thread, fed through a 1/8" PT port.
For real-world sizing, plan on roughly 935 N of usable push at 0.5 MPa (about 0.6 of the rated force), which corresponds to lifting about 79 kg vertically with a 2:1 margin. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits tight gantries and fixtures where a full-length cylinder will not. This -S version carries the magnet, so CMSE or DMSE reed or solid-state switches can be mounted in the body slots for end-of-stroke signalling, and a fixed TPU bumper at each end absorbs stop energy. Speed runs 30-500 mm/s on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi).
Airtac TACE Guided Compact Cylinder TACE63X100S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE63X100S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 100 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1458 N |
| 0.7 MPa | 2182 N | 2041 N |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE63X100S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE63X100S Is Used
Bushing press station
Pressing small bushings into automotive bracket housings on a transfer line: 1558.6 N at 0.5 MPa covers light press work, and the twin-guide yoke keeps the punch square to the bore without an external guide.
Carton clamp on a case packer
A clamping platen that must stay flat against the carton face: the non-rotating guide rods stop twist under side load, and the 100 mm stroke clears the pack pattern while the short body fits the machine frame.
Guard gate lift on a food line
Raising a hinged stainless guard gate of about 70 kg at washdown-friendly cycle speeds: the derived vertical figure of roughly 79 kg with a 2:1 margin matches the part weight, and CMSE switches signal gate-down position.
Is the Airtac TACE Guided Compact Cylinder TACE63X100S the Right Cylinder?
If 1558.6 N of push at 0.5 MPa is more than the job needs, the bore 50 TACE delivers 981.7 N; if the working load exceeds about 935 N, step up to bore 80 for 2513.3 N. Note that the piston drifts when air is lost - for a load that must stay put, add a rod lock or pilot check valve. The 100 mm stroke sits well inside the 250 mm standard range for bore 63, and FB flange, CA/CB clevis, CR or FTC mounting can be specified. The -S magnet is already fitted on this model, so CMSE / DMSE switches bolt straight on without reordering.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE63X100S FAQ
At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N; at 0.7 MPa it pushes 2182.1 N and pulls 2041.3 N; the theoretical maximum is 317.9 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) with proof pressure of 1.5 MPa (215 psi), and speed is adjustable from 30-500 mm/s. A practical planning figure is about 935 N of usable push at 0.5 MPa, or roughly 79 kg of vertical lift with a 2:1 margin.
It is an ISO 21287 short-body design that saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a hard-anodized aluminium body, an S45C hard-chrome plated 16 mm rod and a fixed TPU bumper at each end to absorb stop energy. Because this is the -S version, the magnet is fitted and CMSE / DMSE reed or solid-state switches mount directly in the body slots. Mounting options include FB flange, CA/CB clevis, CR and FTC, and the rod ends in an M10x1.5 female thread.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE63X100S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.