Airtac TACE Guided Compact Cylinder TACE63X20S
The AirTAC Airtac TACE Guided Compact Cylinder TACE63X20S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 20mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke20 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE63X20S
The TACE63X20S is a double acting, non-rotating compact cylinder built to ISO 21287: a 63 mm bore pushes 1558.6 N and pulls 1458.1 N at 0.5 MPa, rising to 2182.1 N on the extend stroke at 0.7 MPa. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square with no external guide. The hard-anodized aluminium body with an S45C hard-chrome plated 16 mm rod runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), 30-500 mm/s, from -20 to +70 C.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why this 20 mm stroke unit drops into tight welding jigs and press fixtures where a full-length body will not fit. A fixed TPU bumper at each end absorbs end-of-stroke shock. Because the S code is in this model, the magnet is fitted, so CMSE / DMSE reed or solid-state switches can be clamped straight onto the body slots. As a planning figure, treat roughly 935 N as the usable push at 0.5 MPa, which lifts about 79 kg vertically with a 2:1 margin.
Airtac TACE Guided Compact Cylinder TACE63X20S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE63X20S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 20 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1458 N |
| 0.7 MPa | 2182 N | 2041 N |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE63X20S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×20 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE63X20S Is Used
EV battery tray bracket staking
The 1558.6 N push at 0.5 MPa stakes terminal tabs on aluminium battery tray brackets, while the twin-guide yoke keeps the punch square over the 20 mm working stroke.
Cosmetic jar lid pressing
On a rotary filling line, the 63 mm bore presses snap-on lids with about 935 N of usable force, and the short body tucks under a low guard where a longer cylinder cannot.
Die-cast housing gripper
Twin guide rods carry the side load of clamping rough aluminium die-cast housings, so the gripper jaw does not rotate, and CMSE switches on the fitted -S magnet confirm jaw closed.
Is the Airtac TACE Guided Compact Cylinder TACE63X20S the Right Cylinder?
For this 63 mm bore the 0.5 MPa push of 1558.6 N sits between the 50 mm bore (981.7 N) and the 80 mm bore (2513.3 N), so step down to 50 for lighter clamps or up to 80 when the 20 mm stroke must also shear or stake harder parts. Note that the piston drifts if air is lost, so a held load needs a rod lock or pilot check valve in the circuit. Mounting is chosen from FB flange, CA/CB clevis, CR and FTC, and the rod end carries a female M10x1.5 thread on the yoke with no male-thread code. PT ports are 1/8" on this bore, and the fitted -S magnet means CMSE / DMSE switches work without reordering.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE63X20S FAQ
At 0.5 MPa the 63 mm bore pushes 1558.6 N and pulls 1458.1 N; at 0.7 MPa push rises to 2182.1 N and pull to 2041.3 N. The theoretical maximum is 317.9 kgf at 1.0 MPa. For sizing, plan on roughly 935 N of usable push at 0.5 MPa, about 79 kg of vertical lift with a 2:1 margin. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof rating.
It is an ISO 21287 compact cylinder whose short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a fixed TPU bumper at both ends to absorb end-of-stroke shock. Mounting options are FB flange, CA/CB clevis, CR and FTC, the rod end is female M10x1.5, and ports are 1/8" PT. Because this model carries the -S code, the magnet is fitted and CMSE / DMSE reed or solid-state switches mount directly in the body slots.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE63X20S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.