Airtac TACE Guided Compact Cylinder TACE63X25S
The AirTAC Airtac TACE Guided Compact Cylinder TACE63X25S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 25mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke25 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE63X25S
The TACE63X25S is a double acting, non-rotating ISO 21287 compact cylinder with a 63 mm bore and a 25 mm stroke. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide. At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N; at 0.7 MPa those figures rise to 2182.1 N push and 2041.3 N pull, with a theoretical peak of 317.9 kgf at 1.0 MPa.
For real-world sizing, plan on roughly 935 N of usable work at 0.5 MPa (about 0.6 of the push rating, close to 95 kgf), or expect it to lift about 79 kg vertically with a 2:1 margin. The hard-anodized aluminium body is about 50% shorter than an ISO 15552 profile cylinder, so it fits tight jigs, guards and gantries. Because this model carries the optional -S magnet, CMSE or DMSE switches can be mounted in the body slots for end-of-stroke sensing. It runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), speeds of 30-500 mm/s, with a fixed TPU bumper at both ends, 1/8" PT ports and a female M10x1.5 thread on the 16 mm rod.
Airtac TACE Guided Compact Cylinder TACE63X25S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE63X25S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 25 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1458 N |
| 0.7 MPa | 2182 N | 2041 N |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE63X25S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE63X25S Is Used
Bearing press-fit on an electronics assembly line
The 1558.6 N push at 0.5 MPa seats small bearings and connectors into housings, and the 25 mm stroke gives a short, fast approach in cramped fixture plates.
Flap-clamp fixture on a carton sealing machine
Twin guide rods on the yoke keep the clamp plate square across the box flap, holding alignment without a separate guide rail beside the sealer head.
Stopper blade on a pallet conveyor line
Mounted vertically it lifts about 79 kg of blade and bracket with a 2:1 margin, and the fitted -S magnet lets a DMSE switch confirm the up position.
Is the Airtac TACE Guided Compact Cylinder TACE63X25S the Right Cylinder?
At 63 mm bore this sits in the mid-force band: the 50 mm bore pushes 981.7 N at 0.5 MPa if your load is lighter, while the 80 mm bore pushes 2513.3 N for heavier press or clamp work. Remember the piston drifts when air is lost - it is not a lock - so add a rod lock or pilot check valve if the load must stay put. Mounting choices are FB flange, CA/CB clevis, CR and FTC, and since this is the -S version the magnet is already fitted for CMSE / DMSE switch mounting.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE63X25S FAQ
At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N; at 0.7 MPa it pushes 2182.1 N and pulls 2041.3 N. The theoretical maximum is 317.9 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, and speed ranges from 30-500 mm/s.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it suits tight jigs and gantries. A fixed TPU bumper at each end absorbs end-of-stroke shock. Mountings include FB flange, CA/CB clevis, CR and FTC. As an -S model the magnet is fitted, so CMSE or DMSE reed or solid-state switches can be clipped into the body slots. Note it does not hold position if air is lost - fit a rod lock or pilot check valve for a held load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE63X25S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.